microswiss 3d models
808 3d models found related to microswiss.thingiverse
Ender 5 Fang for use with microswiss direct drive and 2 x 40mm fans
thingiverse
modified for the ender 3 microswiss dd to fit cr10s pro. ... had to raise bed 5mm set x axis off set to -35 and y to -25
grabcad
This is a mockup of the Microswiss hotend for the CR-10, a basic mockup for the X-carriage is included.
thingiverse
Remixed https://www.thingiverse.com/thing:4808751 Removed cable chain portion so that it's just a replacement MicroSwiss direct drive filament guide.
thingiverse
I remixed this fang (thing:2389245) for my All Metall 300°C Microswiss Hotend. ... (https://store.micro-swiss.com/products/all-metal-hotend-kit-for-cr-10) The fang fits good ..
thingiverse
Couldn't find a Satsana for Ender 3 V2 with Microswiss direct drive and CR touch. ...haven't printed yet, but I will update with probe offsets once installed.
thingiverse
I have not tested this one yet so print at your own risk. ...Just a thought to hard mount a microswiss onto a cooling duct so you have the whole hotend as one piece ready for BMG or whatever.
thingiverse
This is the Microswiss Ender Filament Guide from their available STL. ...I did not create this and am making this available on Thiniverse as it is freely available elsewhere.
thingiverse
This is a drag chain mounting option for a CR-10 with MicroSwiss direct drive hotend. ...The drag chain I use with this was this [10x11 one from AliExpress](https://www.aliexpress.com/item/1005002038905501.html)
thingiverse
Microswiss in their installation instructions for their NG Direct Drive Kit recommend 1.75mm of exposed threads normal filament and 2.75mm of the exposed threads flexible filaments such as TPU. I didnt want to measure so I created a jig based off of...
thingiverse
PRINT WITH BOLT HOLE FLANGE ON THE BED. ... USE SHORT M3 TO ATTACH TO MICROSWISS AS SHOWN. ONLY WORKS IF NO LEVEL SENSOR IS ATTACHED TO MS. SPACER IS 4MM THICK. NO NEED FOR X OFFSET. Y OFFSET NOT NEEDED IF YOU MOVE Y SENSOR ON ENDOR 3. ...
grabcad
I needed support for my MIcroswiss DD wire loom, this includes space for Velcro tie-downs and the use of 2 zip ties to secure the clamp on the bottom. ...This will print with no support, I used PTEG because of its toughness and flexibility.
grabcad
Microswiss hotend compatible with a lot of printers. This hotend keeps the PTFE tube out of the hot zone, thus preventing it from overheating and allowing higher working temperatures. ...This model does not include the nozzle tip but you can download...
thingiverse
This is a simple fan shroud to convert the Creality CR10Spro to a microswiss (clone) hotend. Designed to fit two 4010 radial fans for part cooling and a 40mm axial fan for hotend cooling. includes a bracket for a BLTouch print with the...
thingiverse
MicroSwiss_NG_NOCUT = Channel provided for hotend fan with wire on left side MicroSwiss_NG_CUT_FAN = Hole provided for fan wire that you must cut - better looking MicroSwiss_NG_LEFTWIRE = Channel provided for left wired fan - Looks the best - must...
thingiverse
Upgraded features are as follows: - better nozzel visability - an extra parts fan screw hole for stronger fan fixing - more space between parts fan the mounting plate surface - more defined jets to nozzel - BLTounch mount adjusted for less supports...
prusaprinters
In search for the holy grail of fixes regarding what is mostly known as issue 602 (inconsistent extrusion stuff) I had the idea of trying out a smooth idler on the microswiss DD, it fits a 624zz bearing held in place by M4 bolt.Goes without saying...
cults3d
The original cut Bowden tube that come with the Microswiss setup is too short, and if you print TPU, it will tend to pop out of the side of the gears where the lower tube meets. This jig cuts it a bit longer so it almost touches the bottom of the...
thingiverse
The original cut Bowden tube that come with the Microswiss setup is too short, and if you print TPU, it will tend to pop out of the side of the gears where the lower tube meets. This jig cuts it a bit longer so it almost touches the bottom of the...
thingiverse
I found a model of the full microswiss unit and used it combined with my own measurements to tweak this as close as possible to push the filament right up between the gears. The tolerances are so close, I usually have to sand the outside a bit...
prusaprinters
DEPRECATED DESIGN Please be aware I am not developing this design any further. Microswiss_Cooling_Side_v1.1.stl for side mounting cables now uploaded. Upgraded features are as follows: better nozzel visability an extra parts fan screw hole for...
thingiverse
This adapter allows you to convert a V-wheel Microswiss Direct Drive to a Bowden extruder for additional use after one converts to linear rails. The Extruder works VERY well as a bowden, equally as well as being a direct drive. Just up the...
thingiverse
### Remixes, modding and alternative source As the zip download is still broken, i have decided to make the [repository with openSCAD sorce and STL files](https://codeworks.madmech.de/sebastian/E5-Microswiss-Spider/releases) public. Please do not...
thingiverse
After almost one year of manual (and painful...) bed levelling I've finally got a crtouch for my ender5pro, but I had this printer upgraded to the microswiss direct drive (shortly after buying it), so I needed a mount which could fit my setup. I...
thingiverse
Printed parts required to use the Orion with a microswiss hotend. ... I have not personally tested these parts with a microswiss hotend.
cults3d
Ender 5, Ender 5 Plus, etc. ... Microswiss direct drive chain bracket for the Bretware chain systems.
thingiverse
Modified the Microswiss NG shroud to allow for a noctua 40mm parts fan.