microwave turntable coupler 3d models
13686 3d models found related to microwave turntable coupler.thingiverse
I modeled this from the broken piece with a calipers but it should be a direct replacement for this:...
myminifactory
This is a turntable coupler that will fir the "Home & Co' microwave (Model: EM134AL7)
thingiverse
Replacement coupler for the turntable in a microwave. I found many that were 1.5 in diameter, but could not find one for this 2 inch diameter part. This fits my GE Spacemaker XL, but, I believe it is somewhat common for other microwave...
thingiverse
The turntable motor coupling in my microwave broke. I was afraid it was the motor, but turns out it was just the coupler. Took a couple of measurements and FreeCADded it up. It might fit other Sharp models, but mine was R-930AK-P. ... I printed this...
cults3d
The turntable motor coupling in my microwave broke. I was afraid it was the motor, but turns out it was just the coupler. Took a couple of measurements and FreeCADded it up. It might fit other Sharp models, but mine was R-930AK-P. ... I printed this...
prusaprinters
<p>Use PETG or PC filament.</p><p>Printed at 0.20m QUALITY settings with 40% infill.</p>
thingiverse
Replacement turntable coupler for a Sharp Carousel Microwave oven. ... The inventor file is also included if you want to modify or improve it.
thingiverse
I used ABS and it seams to be working well
thingiverse
The original part has the number W10545578 on it, indicating it's used in a Whirlpool / KitchenAid microwave in the USA, but for me it's for a Lamona HJA7030 fitted microwave oven. It's substantially thicker than the original for strength, less...
thingiverse
Inspired by Natevw's "Microwave turntable shaft coupling" this replaced the worn coupling on my 20+ year old Kenmore microwave. The Kenmore needed a slightly longer shaft and slightly larger hole. ... The original coupling is made of nylon and over the...
myminifactory
This is a replacement turntable support for your microwave. It fits under the glass plate. It fits models from Emerson Radio The reference of the part is 252200100002. ... You can buy it 3D printed on Ebay: https://www.ebay.com/itm/112613960664
thingiverse
Easy to store, low profile cake turntable using the glass tray and roller assembly from your microwave. Has a track for the wheels to ride in and a center pin to keep the plate in place. Note that not all microwave hardware is the same size. Below...
thingiverse
Here is a replacement part for any microwave that has a standard Ø 180 mm 5889W1A012A turntable. It's commonly used in budget devices. All you'll need is a T10-T20 torx screwdriver for the assembly. Max recommended layer height : 0.2 mm Tip...
cults3d
Here is a replacement part for any microwave that has a standard Ø 180 mm 5889W1A012A turntable. It's commonly used in budget devices. All you'll need is a T10-T20 torx screwdriver for the assembly. Max recommended layer height : 0.2 mm Tip :...
thingiverse
I designed this for the shop microwave. ...Connects the revolving plate to the drive motor.
myminifactory
This is a turntable support that will fit the 'Home & Co' mocrowave (Model:EM134AL7).
thingiverse
... the Shaft/Pin to fit . Designed using Fusion 360. Note: This was designed for my Kogan Convection Microwave. Original part lost while moving house. ... The inner diameter of the Mian ring is 215mm and the wheels run around at approximately 225mm.
thingiverse
The microwave at our coworking space was missing the plastic part between the motor shaft and the knurls of the glass tray. Instructions This is the second revision, didn't bring calipers to the...
thingiverse
... circle. Join the parts by melting and then squishing together. So far the part has been put in use in the microwave for up to 10 minutes non-stop and produces no smell and the part is still cold after 10 minutes. ...I'm not sure how PLA would go?
myminifactory
Table Coupler for a Whirlpool microwave oven. ... 2003 Whirlpool microwave Model #: MH6150XMS
thingiverse
Install Use This item may fit tight but, I've come to the realization that since the microwave glass plate weighs down on the table coupler the part does not need to be a force fit on the oven's table motor shaft. The table coupler simply should not...
thingiverse
The shaft-to-plate coupler for a microwave (an old GE model) rotating glass plate. This one's a cross-shape, not the triple-wing thingy you see in most modern ovens. There are two versions of the couplers; one with support vanes, one without. ...
thingiverse
This fits over the shaft of a microwave turntable motor. ... This was specially designed for a GM-16-12F17 synchronous motor.
thingiverse
Motorized turntable done with microwave motor and 5mm steel balls for the bearing. You don't have to use the steel balls if you want because the motor has a very high torque. (2,5 r.p.m.) Plataforma giratoria con motor de microondas con bolas de...
cults3d
Motorized turntable done with microwave motor and 5mm steel balls for the bearing. You don't have to use the steel balls if you want because the motor has a very high torque. (2,5 r.p.m.) Plataforma giratoria con motor de microondas con bolas de 5mm...
thingiverse
LG Microwave turn table bracket had a push fit wheel wear out. Would no longer stay on the round bracket that ties all the wheels together. I dimmed it out and created a new one. It pushed on and worked fine. Printing: Layer Height: 0.2mm ...
cults3d
This is the coupler for microwave oven dish, fits the vast majority of brands. ... Whirlpool, LG, Haceb, Abba, Kalley See attached drawing.
thingiverse
Toshiba Microwave turntable adapter v7.obj This adapter allows new style turnatble on old 80's commercial Toshiba Microwave. Warning! I have not tested this in the microwave. Hence no STL file. Filament material..not sure.? ... Any ideas...
thingiverse
This is an accessory for https://www.thingiverse.com/thing:5419263 When you need a larger surface area, instead of fitting a bearing into the Upper Tray, this attachment allows you to use a microwave plate as the Top Plate. ... I decided to print this...