microwave turntable shaft 3d models

The microwave at our coworking space was missing the plastic part between the motor shaft and the knurls of the glass tray. Instructions This is the second revision, didn't bring calipers to the...

This fits over the shaft of a microwave turntable motor. ... This was specially designed for a GM-16-12F17 synchronous motor.

I used ABS and it seams to be working well

Inspired by Natevw's "Microwave turntable shaft coupling" this replaced the worn coupling on my 20+ year old Kenmore microwave. The Kenmore needed a slightly longer shaft and slightly larger hole. ... The original coupling is made of nylon and over the...

Drive for microwave turntable

This is a turntable coupler that will fir the "Home & Co' microwave (Model: EM134AL7)

... in a microwave. ... I found many that were 1.5 in diameter, but could not find one for this 2 inch diameter part. This fits my GE Spacemaker XL, but, I believe it is somewhat common for other microwave turntables. ...This is GE part: GEHWB06X10138

I modeled this from the broken piece with a calipers but it should be a direct replacement for this:...

This is a replacement turntable support for your microwave. It fits under the glass plate. It fits models from Emerson Radio The reference of the part is 252200100002. ... You can buy it 3D printed on Ebay: https://www.ebay.com/itm/112613960664

Easy to store, low profile cake turntable using the glass tray and roller assembly from your microwave. Has a track for the wheels to ride in and a center pin to keep the plate in place. Note that not all microwave hardware is the same size. Below...

Here is a replacement part for any microwave that has a standard Ø 180 mm 5889W1A012A turntable. It's commonly used in budget devices. All you'll need is a T10-T20 torx screwdriver for the assembly. Max recommended layer height : 0.2 mm Tip :...

Here is a replacement part for any microwave that has a standard Ø 180 mm 5889W1A012A turntable. It's commonly used in budget devices. All you'll need is a T10-T20 torx screwdriver for the assembly. Max recommended layer height : 0.2 mm Tip...

I did however need to increase the hole size of the wheels and Ring parts using with a 4.5mm drill for the Shaft/Pin to fit . Designed using Fusion 360. Note: This was designed for my Kogan Convection Microwave. Original part lost while moving...

I designed this for the shop microwave. ...Connects the revolving plate to the drive motor.

This is a turntable support that will fit the 'Home & Co' mocrowave (Model:EM134AL7).

... circle. Join the parts by melting and then squishing together. So far the part has been put in use in the microwave for up to 10 minutes non-stop and produces no smell and the part is still cold after 10 minutes. ...I'm not sure how PLA would go?

The turntable motor coupling in my microwave broke. I was afraid it was the motor, but turns out it was just the coupler. Took a couple of measurements and FreeCADded it up. It might fit other Sharp models, but mine was R-930AK-P. ... I printed this...

The turntable motor coupling in my microwave broke. I was afraid it was the motor, but turns out it was just the coupler. Took a couple of measurements and FreeCADded it up. It might fit other Sharp models, but mine was R-930AK-P. ... I printed this...

Motorized turntable done with microwave motor and 5mm steel balls for the bearing. You don't have to use the steel balls if you want because the motor has a very high torque. (2,5 r.p.m.) Plataforma giratoria con motor de microondas con bolas de 5mm...

Motorized turntable done with microwave motor and 5mm steel balls for the bearing. You don't have to use the steel balls if you want because the motor has a very high torque. (2,5 r.p.m.) Plataforma giratoria con motor de microondas con bolas de...

The original part has the number W10545578 on it, indicating it's used in a Whirlpool / KitchenAid microwave in the USA, but for me it's for a Lamona HJA7030 fitted microwave oven. It's substantially thicker than the original for strength, less...

LG Microwave turn table bracket had a push fit wheel wear out. Would no longer stay on the round bracket that ties all the wheels together. I dimmed it out and created a new one. It pushed on and worked fine. Printing: Layer Height: 0.2mm ...

Toshiba Microwave turntable adapter v7.obj This adapter allows new style turnatble on old 80's commercial Toshiba Microwave. Warning! I have not tested this in the microwave. Hence no STL file. Filament material..not sure.? ... Any ideas...

Replacement turntable coupler for a Sharp Carousel Microwave oven. ... The inventor file is also included if you want to modify or improve it.

 Upon investigation, the ceramic drive cog that fits between the clockwork motor and the turn table had split on the motor shaft.  A few minutes with my calipers and 3D builder, I sliced up and printed this replacement in less than an...

This is an accessory for https://www.thingiverse.com/thing:5419263 When you need a larger surface area, instead of fitting a bearing into the Upper Tray, this attachment allows you to use a microwave plate as the Top Plate. ... I decided to print this...

Print one of these out of ABS at 100% fill to replace original teflon part that rounds out and prevents turntable from rotating. Why this part was molded from a plastic that creeps and only has a small D shape to rotate a large heavy platter is...

DIY turntable with old clock and microwave motor (motor couplings). ... motor 49TYJ 110/220 - 127/240

<p>Use PETG or PC filament.</p><p>Printed at 0.20m QUALITY settings with 40% infill.</p>

Design based on internet blueprints and phisycal part.