midbass 6 5 3d models
739031 3d models found related to midbass 6 5.grabcad
Simplified model of the budget friendly 6.5" driver from SDS series by Peerless. ...It's a fine match to some of the loudspeaker enclosures I uploaded.
cults3d
This is the first of my Scale Audio offerings, What we have is a flat 6.5 midbass speaker, its designed flat so a hole can be cut/drilled into a door card and these would be slotted in place. The 2 inch Tweeter can be mounted on the door card,...
grabcad
A model of the ScanSpeak 18WU 474T00 Midbass driver. ...One of the best avaliable.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: offset = 2 boltShaft = 3.5 nut = 7.8 gap = 0.3 bridge = 0.3 trap = 2 thickness = 4 washer = 0 wall = 1.6 length = 40 boltHead = 7.1 shaft2 = 5...
sketchfab
Just a little tool to hold a M3 hexhead. ...Official size is 5.5 mm but I made it 6 to account for any inaccuracies. ...Not tested yet.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: nut = 7.8 wall = 1.6 boltHead = 6.7 shaft2 = 6 shaft1 = 5.5 trap = 2 offset = 2 bridge = 0.3 gap = 0.3 boltShaft = 3.5 thickness = 4 length = 40...
cgtrader
A model of the ScanSpeak 18WU 474T00 Midbass driver. One of the best avaliable. ...
sketchfab
TSBW5.5-38-6 DESIGNED FOR: Fixing steel to steel DESCRIPTION: Supertek 6 SIZE: 5.5 x 38.0mm BOX QUANTITY: 200
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options: articulation_thickness = 1.5 diameter_bottom = 6 bolt_diameter = 3 outer_diameter = 20 washer_diameter = 5.5 pressure_point_thickness = 4.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options: washer_diameter = 5.5 bolt_diameter = 3 height = 25 opening_width = 2 pressure_point_thickness = 4.5 diameter_bottom = 5.1 nut_diameter = 6.25...
thingiverse
Ein paar Teile für den Apex 5"/6" von ImpulseRC. ... #####Filamente: - TPU, FoFlex, PLA-Soft/Flex <br/><br/>
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: shaft2 = 5.8 shaft1 = 5 gap = 0.3 offset = 2 nut = 5.8 thickness = 4 bridge = 0.3 length = 30 washer = 0 wall = 1.6 boltHead = 6.7 trap = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1159436 Instructions Using the following options: steps = 6 custom_seed = 0 fuzzy = 5 show_target_circle = yes loop = no holeRadius = 2 show_plate_circle = no ringed = 5 full = 5 plate_diameter...
thingiverse
I tried my best to replicate a real 6.5 Creedmoor round. ...Please leave a comment if you think I should make adjustments to the measurements.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=59332 Instructions Using the following options: _magnetDiameter = 6.6 _sidewallThickness = 1.6 _height = 100 _hingeGap = 0.25 _rounding = 4 _horizontalThickness = 1.6 _length = 70...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=217029 Instructions Using the following options: warmtop = 14 wbase = 8 harmbottom = 5 harmtop = 3.6 hbed = 6.5 warmbottom = 14 laenge = 30
thingiverse
_______________________________________________________________________ Pros Lightweight, quiet, very cheap Cons Low tolerance to heat, durability...