mini 12v generator 3d models
168710 3d models found related to mini 12v generator.thingiverse
This small car has a Raspberry Pi2 B and SD Card with Raspbian Jessie, 4 DC motor on base frame, 2 Dual H Bridge motor driver, 16 channels PWM controller for the motor drivers and TPLINK wireless USB adapter. The software is written in C#. The...
thingiverse
My first tinkering in Onshape.... Just pop that ugly E3D fan shroud off and install this fancy filament cooler! Works with the installed 30mm fan, no need to to upgrade to 40mm (.... ...well, maybe a 40mm fan is a bit more quiet ;) Uploaded fixed 40mm...
thingiverse
Attaches magnetically to the inside of the metal frame. Camera can be tilted up, down, left and right. Requires two M4 screws to connect the 3 pieces and two 12x3mm round magnets. ...The screws are a tight fit on purpose so that the hinges are not too...
thingiverse
Customized version of https://www.thingiverse.com/thing:4621493 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4621493
thingiverse
Customized version of https://www.thingiverse.com/thing:1460407 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1460407
thingiverse
Customized version of https://www.thingiverse.com/thing:1460407 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1460407
thingiverse
a holder for this gps: http://goo.gl/pqBJc6 designed to look a bit like the DJI naza's GPS module. ...i included the 123D design file if anyone wants to change the diameter of the hole where the shaft is supposed to fit, atm it's ~8.5 mm Print Settings...
thingiverse
Leicht zu druckendes Modell eines i3 Mega 3D Druckers. Nur noch die Einzelteile mit Sekundenkleber zusammenfügen, fertig. Easy to print model of an i3 Mega 3D printer. Just join the individual parts with superglue and you're done. ... ...
thingiverse
The acrylic endstop brackets that came with my kit did not accept the endstop PCBs well. They were also rather narrow where they mounted on the 2020 extrusions. I designed these brackets to suit my requirements. The PCB mounting holes are small...
thingiverse
Same as the regular TUSH, just shortened to work with the small 250g spools. ...608 bearings snap in just fine.
thingiverse
Ever had to throw away one of those tiny but still quite useful tripods, or have you got (like me) a bunch of them lying in a drawer somewhere because you managed to lose or simply break that little threaded cuff/hat/ring (whatchamagadget)? I got...
thingiverse
Remix of: https://www.thingiverse.com/thing:3315290 Made it 5% larger (so photo doesn't bend),and added larger holes for stronger 6x2MM magnets. The magnet fits perfectly, but I still put a dab of super glue on it. ... Great, simple design by ...
thingiverse
I made these key holders for my friends during lockdown. Can use sticky pads for the back and attatch them to the wall. ...Will fit any of the R56 keys (the ones that are round, unlike the pill shaped F56 keys)
thingiverse
Customized version of http://www.thingiverse.com/thing:537516 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=537516 Instructions Using the following options:...
thingiverse
This is the part of the PropellerSaver that sits on the motor shaft. Print with raft and 100% fill - preferably several at a time so that the layers have time to cool. ... Print upright with the narrow side down without suppport.
thingiverse
https://youtu.be/MPdxeomm52c Truck body and suspension prints in one piece. No need for support, supports are built into part. Rim caps friction fit to body, no glue is needed. The print shown here was done with PLA using standard settings. For a...
thingiverse
After my manga books wandered all over my house, I finally took it upon myself to build a place for them. If you have glue, I recommend using it to glue the back panel to the side ones, that's until I learn how to make them do it without the...
thingiverse
Customized version of http://www.thingiverse.com/thing:1583409 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1583409 Instructions Using the following options:...
thingiverse
Printing the first times with my Kossel XL, I found out that there are some pretty noisy low frequency things going on. You did not here that right next to the Printer, but in the next room. So I wanted some very soft vibration dampers, but the...
thingiverse
Glass holder for 200 mm glass. ...Print Settings Printer Brand: Deltaprintr Printer: Deltaprintr Kit ...
thingiverse
Collectible figure of the Uber Soldat, themed after Wolfenstein 2009. ... Includes: Full figure with mask Full figure with Despoiled skull Stand with TNO logo https://www.patreon.com/posts/86144551
thingiverse
Макет подставки для Яндекс мини 2 с часами , нужно разобраться с подержками, можно доработать. ... Прошу уведомить или оставить комментарий если будет чтоб тоже смог посмотреть что у вас получилось.
thingiverse
Remixed feet to look like more dragon or reptile. customized with 3D Slash! ...Print Settings Printer Brand: RepRap Printer: ...
thingiverse
Remixed the head to look like a knights helmet instead. ...Print Settings Printer Brand: RepRap Printer: HICTOP ...
thingiverse
This simple spool holder design can be screwed on a desktop. It can handle any kind of spool. ...The 3D printed spool on the picture is this thing: http://www.thingiverse.com/thing:293382 The sketchup file is provided Print Settings Printer: ...
thingiverse
https://youtu.be/ov3933mt2-A Simple decoration of LED candle. Making is easy! When you print out this model, I recommend the 100% infill on slicer setting. My modeling is thin enough to transmit light. ...There are diverse decorations with LED...
thingiverse
Customized version of https://www.thingiverse.com/thing:2701137 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2701137