mini itx case with atx power supply 3d models

This is a simple test bench fitting a Mini-ITX (17 x 17cm) motherboard and an ATX power supply in vertical position.

mini itx case modified for power supply

Made this to test some equipment The 4 holes on the bottom are for SSD Flex ATX Power Supply...

A case for an ATX power supply with labeled spots for Anderson PowerPole connectors. I also included holes for 2 volt/ammeters from...

ATX Power Supply Case Print instructionsThis is a simple model to print, but before you do check that back ports of your supply fit into holes and redesign if they dont. On the side there is a port for usb cable. ...I cut one old usb extension cable and...

mini-pc con 4 posti per ssd nella parte sotto compatibile per schede madri micro-atx e mini-itx compatibile solo con alimentatore mini-itx i due fori dietro sono x uscita on-off scheda madre e connettore alimentatore esterno non sono presenti punti...

A power supply cover I designed around a DELL ATX power supply. To eliminate support material, I decided to make the top portion foldable. Holes fit standard Banana plugs. ... The top is attached with aluminum tape, that part could use improvement.

A simple case for an atx power supply. Hides all the extra wires while still letting it breath and stay cool. ... ** Be sure to flip the back plate over before printing, the underside has a large overhang ** This requires two #4 self tapping screws,...

Carrying around my ATX power supply for my heated bead was a real pain so I used http://www.makercase.com/ to make an easier way to carry my printer and power supply at once. Notice that the ATX power supply fan is also cooling my Printrboard. There...

This is a simple case to convert a standard atx power supply to provide 6 outputs. I have used it as 5v, 2x 12v and 3x Ground but any configuration is possible even 3.3v. Knowledge in electrics is required and usually there is no need to open the...

Velka3 Mini-itx PC case all files for manufactured. ...FlexATX Power supply

Power supply cover with on/off switch, indicator LED and socket. ... Last picture LED is "on", plugged in and working.

This case was designed to re-use an ATX power to supply 3.3V, 5V, 12V and -12V in bench projects with fused protection without damaging it (no need to cut or modify any cables). The power supply fits securely in the case and can be easily removed...

Handle for ATX power supply case. ...Designed to carry DIY devices assembled in an ATX power supply case. Allows for winding the power cable, has holes for fixing the plug type F. ... For mounting, use M4 screw and injection nut or hex nut.

Designed to carry DIY devices assembled in an ATX power supply case. Allows for winding the power cable, has holes for fixing the plug type F. For mounting, use [M4 screw](https://www.aliexpress.com/item/4000970993800.html) and [injection...

This is an custom case (face) for PSU made from: 1) modified ATX power supply for 30V (see http://vlad-gheorghe.blogspot.ro/search/label/2003 ) 2) switching module for 8A (...

ATX power supply skeleton case 1x ATX power supply 1x https://www.laskarduino.cz/prepinac-kolebkovy-3a-250vac-kruhovy/ 3x https://www.laskarduino.cz/panelovy-digitalni-voltmetr-ampermetr-100v-10a-dc/ 3x...

Rebuild an old computer power supply to a new custom bench power supply with 3.3v, 5v, 12v, USB and a adjustable voltage and current output. I added an extra module for 9V for my Arduino projects. I'm not sure if it all fits the case. I added this...

its a simple open case, for micro atx (mATX) and mini itx desktop boads. with atx psu support, and a single 2.5 ssd/hdd.... Really uncomfortable to mount, but works, and other accesories, ideally for an m.2 device there are 2 pieces. base, the...

ATX power supply skeleton case 1x ATX power supply 1x https://www.laskarduino.cz/prepinac-kolebkovy-3a-250vac-kruhovy/ 3x https://www.laskarduino.cz/panelovy-digitalni-voltmetr-ampermetr-100v-10a-dc/ 3x...

I unsoldered the wires with molex, IDE power and the drive from the power supply board. The adapter board and the voltmeter board are fixed with M3 screws and soldered nuts. The plastic housing is attached to the power supply housing with M4...

Fits standard Mini-ITX Mainboards (shown with an ASROCK Z390M) and standard SFX Power Supplies (shown with a BeQuiet SFX Power 3). SFX-L and ATX power supplies will NOT fit in! Requires a buildplate size of 210x180 mm or larger. Does not contain...

For the variable power supply, i used a CN6009 module: https://www.aliexpress.com/store/product/1PC-New-Arrival-CN6009-DC-DC-boost-power-regulator-module-output-adjustable-5V-6-9-12V/1959068_32823927957.html just desoldered the trimmer and soldered...

İt has seven power out ports 3 - 5 v 2- 12v 2-3.3 v This power case has 2 amper and voltmeter port on front side my amper and voltmeter is in this link https://www.aliexpress.com/item/32310008404.html // update fusion file added //update version 2 is...

This is an ITX pc case which fits an ATX PSU and standard ITX parts. )The PSU is mounted with three standard pc case screws. )The mainboard needs standoffs first. These need to be melted into the plastic with a soldering iron for maximum strength.

Cyclone PCB Factory ATX Power Supply Case

Components I used (I took measurements from these parts to design the Borg Case, but I think all the mechanical attachment dimensions are standardized): - Motherboard: ASRock H270M-ITX/ac LGA 1151 motherboard (this board looks to be discontinued,...

This is a custom case for the super cool ATX bench top power supply PCB available from http://www.jordandsp.com/ATX-bench-top-power-supply-adapter.php

Adapter for 1U Flex Power Supply to fit in ATX case.

Alternative panel for Lab ATX power supply skeleton case by james_III