thingiverse
Replacement latch for Kodak mini digital camera Instructions To remove the old broken latch, you will need to press out the pivot pin with a map pin. Print as a solid. The hole for the pivot pin may not print, but you can set the latch in location...
grabcad
Mini-IO latch for 3D-printing Less breakable (depending on your print work)SLS- printing is recommended, FDM also works.
cults3d
- Plastic catch counterpiece for Mini-Latch automatic spring pressure touch latch. Push to Open. ... This counterpart is used to breaking and the manufacturers do not sell it separately, they always sell it with the latch mechanism that is not...
thingiverse
A replacement set including a mini latch and hook isn't available in local hardware stores and would have cost near $10 by internet. I only needed the plastic hook, so, I set out to design a replacement that I could easily turn out with my 3D...
thingiverse
you need to pause the print at 3.5mm so you can manuely install a m3 nut then you can resume print also when mounting the nut it can me good to preheat the nut a little so it is a perfect fit
thingiverse
... Print Mini_Talon_Hatch_Latch_-_Hatch_Pins.STL for the front of hte Hatch to retain the Guide Pins. ...The holes are sized for Bamboo skewers, but I highly recommend .125" carbon or Fiberglass and resize the holes with a drill bit as necessary.
thingiverse
HOW TO ASSEMBLE THE LATCH Before gluing anything together use the top plate as a guide to cut the hatch on the Mini Talon. Take the top plate and set it at the rear of the hatch. Mark all 5 tab locations using the top plate Remove the top plate...
thingiverse
This latch was designed to hold closed the door to a Whirlpool mini fridge without interfering with its normal operation. It uses the existing holes for mounting the hinge on the left side. ...All of the parts are in one stl.
thingiverse
Along with the Hinges (http://www.thingiverse.com/thing:755437) and the Stress relieving washers (www.thingiverse.com/thing:755320), these printed parts make the Complete door assembly for the Lulzbot Mini Enclosure. The enclosure minimizes the...
pinshape
Added a slighly larger version of the latch, less critical on the printing dimensions.InstructionsThis latch was printed at 10% fill and a single shell. Depending on the quality of the print, it may require a little touching up to mate. Bolts...
thingiverse
(I made the holes smaller so that you can drill them out to whatever you like) After printing, test that the latch slides smoothly in the housing if not use fine sandpaper to clean up the edges of the latch. Now go ahead and CA glue the latch...
thingiverse
Useful for both outdoor and indoor, I use it for my rabbit cage. ...Uses a pen spring. 60% scale from original design: http://www.thingiverse.com/thing:8255 Print Settings Printer: Fabrikator Mini Rafts: Yes Supports: No Resolution: 0.2 Infill: 75
cgtrader
Mini Chest with Latch 3D model PBR Textures in 4096 x 4096 All Preview Renders were done in marmoset toolbag 3.08 From the Creators at Get Dead Entertainment. Please like and Rate! :) Please contact us anytime for assistance. ...
grabcad
This is a model of a Southco Nylatch 2-piece Panel Latch (Mini Grip style) made from Nylon as the plunger and polycarbonate as the grommet. These plastic latches can be used to fasten two pieces of material that can be plastic, metal, or even wood.
thingiverse
Customized version of https://www.thingiverse.com/thing:755496 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=755496
thingiverse
There are two options, one has a latch panel suited for a M3 hex nut and the other (my personal preference) is suited for Heat-Set inserts [found here](https://www.mcmaster.com/94180a331). A 10mm M3 screw will also be needed in order to secure the...
thingiverse
This is a replacement latch for the Drazzticaction/Tabsynth enclosure for a Lulzbot Mini Print Settings Printer Brand: LulzBot Printer: Mini Rafts: No Supports: No Resolution: Standard settings in Cura Notes: While I was reprinting the hinges and...
thingiverse
One of small arms in my TRS-80 Mini Disk broke - this replaced it
thingiverse
... also fit the TAZ 5. I printed it with ColorFabb nGen, but I would recommend ABS or ColorFabb XT or HT, or any other strong filament. Print Settings Printer Brand: LulzBot Printer: Mini Rafts: No Supports: No Resolution: .2mm Infill: 70% or higher
grabcad
Ledex Solenoids STA Mini Pull Magnetic Latching Solenoid — 1/2" Dia. ...x 1/2" http://www.ledex.com/ltr2/access.php?file=pdf/Miniature_STAMini_0.5x0.5_Pull-L.pdf
thingiverse
I replaced the ziptie tie by a latch which holds everything very tight, needs no ziptie on the top and looks quite clean. I printed with 101.5% scale for a perfect and very tight fit. Be careful when you divide the both latch parts. Depending on...
pinshape
Use with Lulzbot Mini Acrylic panel profiles: http://www.thingiverse.com/thing:994992 and http://www.thingiverse.com/thing:756211 and http://www.thingiverse.com/thing:756173 If you're interested in a kit of all the laser cut panels and printed parts...
thingiverse
Use with Lulzbot Mini Acrylic panel profiles: http://www.thingiverse.com/thing:994992 and http://www.thingiverse.com/thing:756211 and http://www.thingiverse.com/thing:756173 If you're interested in a kit of all the laser cut panels and printed parts...
thingiverse
... qui avec le temps a pu se déformer.. Sliding glass latch for Austin mini break countryman or mini Morris traveller. ... I attach the Freecad file so that you can adapt it to the exact width of your metal part which over time may have deformed..
thingiverse
Prestige Mini Latch is used in cabinet door for press open/press close function. The mini latch comprises a metal part and a plastic part. ... If the plastic part is broken, it can be replaced by this thing.