mini pir 3d models
88121 3d models found related to mini pir.thingiverse
I have designed here a housing for a Mini Pir. The hole size dia is 11mm It was designed to house this pir under a step on my stairs. ... There is a gap at the back to allow cable entry.
thingiverse
Recessed holder for mini PIR motion sensor. Total (surface) diameter: 18mm Hole (drill) diameter: 14mm (drill) depth: 35mm Inner diameter (for PIR): 10.95mm PIR sensor can be pressed in. Maybe need a little glue or a small piece of tape to stay in...
prusaprinters
I have designed here a housing for a Mini Pir. The hole size dia is 11mm It was designed to house this pir under a step on my stairs. There is a gap at the back to allow cable entry. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No...
thingiverse
Halter für einen Mini Bewebungsmelder z.b. ...https://www.amazon.de/Velleman-PIR415-Mini-PIR-Bewegungsmelder-Einbauen/dp/B006Y66Z8U
thingiverse
This is the Mini PIR insert that will allow the PIR to still function as a button, replacing the original power button of the Sonoff S20. You can find the video [here](https://www.youtube.com/watch?v=sjQHWKdPN7g). ... You can buy the pir here:...
thingiverse
With ESPEasy installed on the Wemos D1 mini, wired to the PIR sensor, it sends a MQTT request to my Mosquitto server and lets me turn on some lights with a timer.see The PIR Sensor cover is glued to the bottom of the case and the top too, to prevent...
thingiverse
The WeMos D1 Mini uses the PIR to detect motion and sends a message over my MQTT broker I run. At the same time the WeMos is capable of receiving instructions from MQTT to switch on the lights in my room by transmitting the KlikAanKlikUit protocol...
thingiverse
... stand for a tiny pir sensor with a high and low level output. ... https://amzn.to/2UAEzqt Is working just fine with the arduino, or a esp8266 board like the wemos d1 mini: https://amzn.to/2HvLlds A great feature for automatic lighting or security...
thingiverse
The enclosure also fits a DHT22 and a pir motion sensor starting from the Wemos D1 mini enclosure project by Dendrowen ( https://www.thingiverse.com/thing:4905266 ). In my customization I wanted to put the motion sensor directly into the wemos...
thingiverse
I extended the length and moved the USB hole back to make room if you already have the pin connectors soldered on the D1
thingiverse
An enclosure to hold a D1 Mini Lite and HC-SR501 PIR sensor. The HC-SR501 can give a lot of false positives because of signals from the ESP8266. This enclosure can make that worse because the D1 Mini antenna sits right below the HC-SR501. For this...
thingiverse
Boitier pour 2 capteurs de mouvements HC-SR501, un capteur DHT22 et un BH1750 connectés sur un wemos D1 mini -------------------- Enclosure for 2 HC-SR501 motion sensors, a DHT22 sensor and a BH1750 connected to a wemos D1 mini
thingiverse
... wich fits on an usb plug. ...Inside is am eps8266 d1_mini board and an PIR-Sensor(HC-SR501). There is no mechanism to hold the cover, so i used clear adhesive tape. ...The box has two holes on one side to control the potentiometers of the PIR-Sensor
cults3d
... wich fits on an usb plug. ...Inside is am eps8266 d1_mini board and an PIR-Sensor(HC-SR501). There is no mechanism to hold the cover, so i used clear adhesive tape. ...The box has two holes on one side to control the potentiometers of the PIR-Sensor
thingiverse
Parts used: - Hc-sr501 Pir Motion Sensor - Wemos D1 Mini - Generic 5v 1A USB Power adapter (like the old boxy apple ones) - Micro USB cable **IMPORTANT: Be sure to power the Hc-sr501 from pin 3 of the mode slection jumper with 3.3V from the Wemos!**...
cults3d
I had to extend the case lengthways to incorporate a slightly bigger Wemos d1 mini board (34.5mm) and also had to extended the height to fit the HC-SR501 PIR sensor. I put screw holes in to screw the PIR to but It pretty much friction fits in place...
thingiverse
I had to extend the case lengthways to incorporate a slightly bigger Wemos d1 mini board (34.5mm) and also had to extended the height to fit the HC-SR501 PIR sensor. I put screw holes in to screw the PIR to but It pretty much friction fits in place...
thingiverse
Dual SR-HC501 PIR sensor facing opposite ways. ...The enclosure includes rail for attaching ESP8266 in the Lolin Wemos D1 mini form in the lid. ...
thingiverse
I've modified the Case for PIR and Wemos D1 Mini to give access to adjust the dials to control the motion distance and duration, added more depth so I could use the dupont cables by just bending connectors slightly towards the middle of the case,...
thingiverse
I bought some ESP32 cameras, M5Stack model found here for example http://bit.ly/2YwdNRG I wanted to use it as a doorcam with home-assistant.io so I made a box with room for a AM312 mini PIR that connects to the GPIO ports and a gopro mount. ...
cults3d
I bought some ESP32 cameras, M5Stack model found here for example http://bit.ly/2YwdNRG I wanted to use it as a doorcam with home-assistant.io so I made a box with room for a AM312 mini PIR that connects to the GPIO ports and a gopro mount.
thingiverse
An Esp8266 Wifi based with a mini PIR motion detector for Domoticz. The Esp8266 is a Wemos D1 mini. The motion detector is powered by a 18650 rechargable battery, which is rechargable by an external micro USB-connector. The PCB for the Lithium...
thingiverse
I printed a case for Wemos D1 Mini and PIR. There are 4 holes for wall mount. ...I send to my MQTT broker, when its detect action and switch lights on in my smart home DIY
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/2kl8TRZWfYj