mini platform 3d models
114032 3d models found related to mini platform.thingiverse
... for gaming though, where you only need discrete 25mm (1 inch) increments. I might change this design to accommodate that at some point. A loop of tape on the platform helps a lot with keeping the mini attached when the stand wobbles. ... Enjoy!
grabcad
This design uses a Arduino Pro-Mini (3.3 or 5 V) and an MCP4231 dual channel digital potenitiometer to control a resistive dimmable light. The system could be adapted for battery or adapter power. ...The application is for controlling industrial parking...
thingiverse
This is a new platform for the OpenScan Mini. ... Main differences from the stock ones - Hole in the middle to add a custom mount - Wider - It's easier to fit on the servo peg
thingiverse
:) This gave me the idea to build the platform: https://www.thingiverse.com/thing:2946700 This platform is 60x60 mm big. My design has slots for nuts, to assemble the too parts. Hammer 4 nuts in the slots, align them with the printed holes and...
thingiverse
A replacement for the part that attaches the bed's frame to the bearings.
thingiverse
So I made this so that I could put up my miniatures onto my corkboard. That's about it There are two model files attached to this thing. One for solidworks and the other a normal stl file. The size of the pin should be around 1cm in diameter...
thingiverse
This is a stand for 1" miniatures with a counter built in. Pics are of a two digit one but you can stack as many or few as you like. ...Superglue was used for assembly.
thingiverse
Instructions Before you print it, check yours UP Mini building platform for this bending in the center issue. If the center is higher than the corners, just print this thing and put it instead stiff old one. Also check the lengh of screws, I had to...
thingiverse
Quick and easy mounting platform for the Myflydream mini crossbow antenna tracker. I just used Velco to mount a immersionRC video receiver to it. ...But I would imagine it could be used in a few different ways.
thingiverse
this is a robot platform I have been working on , with 2 frames for different applications. One has 4 wheels ( skid steer 4 motors) and the other has 3 wheels (servo steer 2 motors). motors are the little yellow plastic ones that come with wheels...
thingiverse
This is for phrozen sonic mini build platform, to hold the platform to drain the resin after the printing. Even during the printing you don't have to remove the holder. ... Note: you don't have to remove the screw but be sure you have pushed the holder...
thingiverse
Good fit. You will need a 3x.5 mm tap and a #40 (.098) drill to size the holes that need tapping. Be careful installing the wood screws. You may need to widen the wood screw holes slightly so they don't crack the ABS. Wood screws hold the wind...
pinshape
Summary Good fit. You will need a 3x.5 mm tap and a #40 (.098) drill to size the holes that need tapping. Be careful installing the wood screws. You may need to widen the wood screw holes slightly so they don't crack the ABS. Wood screws hold the...
thingiverse
You just print three base pieces and three top pieces, and bolt them together to get a respectable-sized platform. The links I'm using are Traxxas 3645 Turnbuckles / Toe Links, 61 mm (pair) (http://a.co/0WOcN2x). They fit an M3 bolt just about...
thingiverse
This is a simple resin draining rack designed for Phrozen Sonic Mini 3d printer. To install, after the print finished, simply slides in and lock the rack with the resin vat nut. Fasten the build platform in an angle at the top. The space should be...
pinshape
Platform ___ 3D Design Tool: SketchUp Pro miniMe's robots are built on top of an open source Arduino-based(ESP8266) platform. Rover Self Balancing Robot Line Tracer RC Car HomeIoTBot Etc... Hardware Base Plate(Parts): 3D Printing ...
thingiverse
Platform ___ 3D Design Tool: SketchUp Pro miniMe's robots are built on top of an open source Arduino-based(ESP8266) platform. Rover Self Balancing Robot Line Tracer RC Car HomeIoTBot Etc... Hardware Base Plate(Parts): 3D Printing Electrical 1 x...
youmagine
Platform 3D Design Tool: SketchUp Pro miniMe's robots are built on top of an open source Arduino-based(ESP8266) platform. Rover Self Balancing Robot Line Tracer RC Car HomeIoTBot Etc... Hardware Base Plate(Parts): 3D Printing Electrical 1 x WeMos...
pinshape
Summary Ever worry about the magnets not being strong enough to hold your extruder in place? Give this a try it works good. Instructions Straight forward installation just like the standard design. Push the stepper motor back into the mangets. ...The...
thingiverse
Ever worry about the magnets not being strong enough to hold your extruder in place? Give this a try it works good. Instructions Straight forward installation just like the standard design. Push the...
thingiverse
調整後傾角度並將銳角改圓角使成型台上下運作時不會碰到,可減少拆卸次數。
thingiverse
This is a modular file that contains specs for platforms in widths, depths, and heights in all combinations of of 2", 3", and 4", as well as 2", 3", and 4" stairs that can be used to transition between them. Stairs also come in two widths - one is...
thingiverse
I used the H-couplers to design a back-mounting platform for the mini rover to allow for mounting of the battery and an upper level for the Arduino and associated components. I did not design the H-coupler, just added a platform on top of two of...
thingiverse
This goes together with this mini-talon canopy remix: http://www.thingiverse.com/thing:1831545 It's a very simple rectangular mount for you FPV and HD camera to fit on the 180 degree servo from Banggood...
thingiverse
Compré un mini torno en Aliexpress que funciona bien, pero prefiero usar insertos de carburo con su soporte. Con las piezas base del torno, la herramienta de corte quedaba muy alta, así que diseñé un soporte más bajo para nivelar la herramienta de...
thingiverse
Here is a video of it working https://www.youtube.com/watch?v=aSNia01SjYs Instructions Arm and platform need support. Drill all of the #4 screw holes to .089-.093" for thread and .120" to go through part. For #15 brad nails cut to length with dikes...
thingiverse
... ...Thanks thatjoshguy for the dimensions of the screw holes. Please note the top is not flat so you need some tilt to mount a camera. I hope this can help enhance your mini skyhunter. About 16 grams with 3 perimeters and 20% infill. ... Cheers!
thingiverse
This is a mount I designed for the ReadyMadeRC Mini Skyhunter, also known as the Eachine Micro Skyhunter, Sonicmodel Mini Skyhunter, etc. This is for the mid-sized version, not the full Skyhunter nor the Nano. This mount is to be used above the...
thingiverse
This is a platform for running a heating cable under the Tar Heel Mini Hearth XL. More models to come for other sizes. ... Feel free to message me for customer models.