mini quadcopter 3d models
94074 3d models found related to mini quadcopter.thingiverse
This is mini quadcopter motor mounts 12X14mm motor diameter 20mm controller hole 45mm esc size 20X25mm
thingiverse
Mini Quadcopter More info:http://blog.lowres.xyz/2015/12/mini-quadcopter.html Still needs some tidying up but its a good prototype. ...Legs 9mm Arms 10mm Props 6x4.5 Battery 4000mah S4
thingiverse
Here is my take on the Mini Quadcopter frame, for complete build instructions https://www.element14.com/community/community/project14/month-of-robots/blog/2019/05/14/mini-quadcopter
prusaprinters
Mini Quadcopter More info: http://blog.lowres.xyz/2015/12/mini-quadcopter.html Still needs some tidying up but its a good prototype. Legs 9mm Arms 10mm Props 6x4.5 Battery 4000mah S4 Category: R/C Vehicles
thingiverse
Frame for a mini Quadcopter. I use 8mm motors, a Quanum Pico, Rolling Spider Props and a 700mah battery. It flys a bit wobbly, and I am not sure yet if there is to less space between the props or if I just need to tune my PIDs... Battery is below the...
thingiverse
Mini Quadcopter. Designed for: Quanum Pico / Micro Scysky Board 8,5mm brushed motors Parrot Rolling Spider Props 700mah battery 1S Upper and lower deck should be attached by Nylon Spaces, length depending on the size of the battery. Battery is fixed...
thingiverse
I have created this because I wanted to design a quadcopter for brushed 8520 motors and the SP3 Racing F3 Evo brushed, which I can fly indoors. I also designed a propeller protector. This version is flying pretty good in my opinion, where previous...
grabcad
Just a rendering and video of Nathan's 3D Printed Mini Quadcopter 3D Printed Mini Quadcopter
thingiverse
Mini quadcopter drone concept. Designed to house a Lemon-RX DSMX Satellite receiver, F3 EVO V2 Brushed flight controller and 8.5mm brushed motors. This is still work in progress as I intend to add FPV and other battery clips for larger batteries...
grabcad
A 3d printed mini quadcopter that I designed, printed, and test flown. The quadcopter has a motor-to-motor distance of 10 inches with 5x3 propellers. The flight controller is a Naze32 (32bit processor, 6dof MPU6050, baro, mag). UPDATE: Well I...
pinshape
Summary Mini Quadcopter Frame free 3D print model This 3D printable quadcopter frame is suitable for "Hubsan X4 H107" mini quadcopter electronics ,you can buy them from the internet such as it's motors (any 7mm diameter motor will fit well in the...
thingiverse
My mini FPV Quadcopter. ... Camera : Eachine TX03 Flight controller: https://abc-rc.pl/kontroler-brush-6dof-fpv Battery: https://abc-rc.pl/akumulator-tattu-3-7v-600mah-30c Props : https://abc-rc.pl/smigla-lantian-55mm Receiver:...
thingiverse
Hi find my new designs a mini quadcopter 280 https://www.youtube.com/watch?v=GiyyGyVObJo&feature=youtu.be https://www.youtube.com/watch?v=ZKEOpDWLVMs&feature=youtu.be 31/07 Frame modified for Pla Filament so the photos and videos will be modified in...
thingiverse
A simple printed mini quadcopter frame. It features a press fit battery holder, receiver holder, and electronics IMU shield. I brought this with me to the Midwest RepRap Festival in March 2013 and several people asked for me to put it on...
thingiverse
I wanted to make modular components for a mini quadcopter (6mmx15mm bushed motor) and came up with this design. It is still a bit on the heavy side but it is a good base to start from. There is a left & right hand side motor mounts print 2 of each...
thingiverse
This is a small quad copter that is designed to be customised to your specs, it can be configured to have a stack controller and esc design or can be used with Arducopter or other like flight controllers. Its designed for small motors and there are...
thingiverse
... a plug that would go into the holes if you mounted the motor on top. i just hot glued the landing gear on to test how it would hold up and so far it has not fallen off. Mini Flame Wheel Quadcopter Frame. ...(http://www.thingiverse.com/thing:34552)
thingiverse
... Legs (feet?) are press fit. Longer ones give enough space for mini camera. If you use different extrusion width, drop me a line. ...I will upload OpenSCAD src when cleaned up :) Engines and control board were scavenged from a "lady bug" model.
grabcad
This quadcopter has a 110*110*5 mm frame and is for the use with 8mm diameter dc motors. ...I'm working on this quadcopter and will upload a video when i finish the project.
thingiverse
This is a bottom frame and motor support for the CJMCU quadcopter that is available at Goodluckbuy.com http://www.goodluckbuy.com/micro-quadcopter-flight-driver-controller-9dof-9-axis-altitude-sensor-stm32f103.html The frame only weights 3 gram. ...Best...
thingiverse
This is a little hanger that can be used on the edge of things like the 'Billy' bookcases from Ikea to hang your little quadcopters from out of the way. ... Happy printing!
grabcad
A tiny quadcopter, about 10cm diameter with 2MP camera and removable 150mAh battery. More info here: http://www.rcdronearena.com/2016/02/06/jjrc-h30c-camera-drone-wants/CAD model made completely from scratch using only a tape measure, but don't be...
thingiverse
I needed a quadcopter wall mount and couldn't find any decent options so decided to make my own. It fits 3M wall tape ( meant for their wall hooks) which is extremely strong. You may need to cut off just the tip of the tape (non-sticky area) for it...
thingiverse
The CopterFX Craze250 is a 250 class quadcopter designed for sport flying and FPV. This is a beta release with improvements to come! Quick Update: Orientation of files corrected. ... Instructions...
thingiverse
I didn't feel like spending money on quadcopter cases with foam inserts, so I got a cheap organizer case from Harbor Freight and designed this hold-down. Slots are suitable for 12mm velcro straps. Harbor Freight Case: ...