mini racing quad 3d models
152881 3d models found related to mini racing quad.thingiverse
Weight w/o/ battery: 420 grams Flight time with 2200maH battery > 7 - 7:30 minutes ( with mobius and VTX ) https://www.youtube.com/watch?v=cFCEnaaKUqY I wanted to print my own frame for a mini racing fpv quad .... also included a center plate for a...
thingiverse
This is a simple light bar that i made for a mini race quad, The mounting holes are M3 and they are spaced 42mm apart. ...You can find the light strip here: [http://tinyurl.com/q3n9c88] Any questions, feel free to ask!
thingiverse
I needed firewalls for some racing quad motors that I wanted to use for FT Mighty Mini planes. However, due to the stiffness of the power wires for these motors, the normal "cross" mounting orientation with the corner cutout for the wires would not...
thingiverse
I had to rethink my work as a result of various flight tests, I noticed that the attachments were inadequate, so now I planned to drill notches for this purpose and to pass a screw on motor support and rizlans/serflex for frame. these parts are...
thingiverse
Compatible with: -XIAOMI YI camera -2204 motors -6inch props -mini size VTX TS5828 or TS5823 -DAL 700TVL fpv camera, or any 32x32 camera RTF weight around 700g Edit: 07/27/2015: updated clean lower, was badly hole for xiaomi strap. ... 07/30/2015:...
thingiverse
addon for http://www.thingiverse.com/thing:933903 Regards, Alex
prusaprinters
Mini race quad 210 frame antenna mount Category: R/C Vehicles
myminifactory
Here are 2 modifications I made for the latest mini race quad from JJPRO. ...After damaging the lipo battery I decided it needed better protection and the way the receiver and esc's are mounted underneath leaves the venerable during landing, so here is...
thingiverse
This is a 250 sized racing quad. I am running emax mt1804 motors with 3 bladed gem-fan props. the flight board is a naze 32 rev 5. ...I am new to the naze, but am enjoying it so far.
thingiverse
Wall mount for mini quads. ...Print Settings Printer Brand: Prusa Printer: Prusa Clone ...
thingiverse
Print 1 each of main stand parts and print two spacers and you have a racing quad starting block. You can use a tent spike or similar to fasten the start block securely by using the hole provided in the middle of the spacer. ... There are 2 different...
thingiverse
Racing drone battery/lipo protector - fits 74.5mm(lenght) x 35mm(width) lipos. ... Print in TPU.
cults3d
Credit card size snap fit racing drone model Just print and assemble (add glue if you want to)
thingiverse
Credit card size snap fit racing drone model Just print and assemble (add glue if you want to)
thingiverse
3 inch is the new 5 inch and that is why I designed a new frame with a new pod that can handle the new power that the 3 inch quads get with there new motors, esc's and fc's. That plus the low weight makes this combo a very fast and strong option for...
thingiverse
https://www.rcgroups.com/forums/showthread.php?3231185-3D-Printed-Micro-Quad-Racing-Gates&perpage=100#post41158827 Update: Because I found a wall here that has a little flange(?) at the corner, I added a second corner bracket which has some...
thingiverse
Leg for KDS250 quad to lift it up out of the wet grass to stop electronics shorting. Requires two more motor screws on each arm. ...Print Settings Printer: K8200 ...
thingiverse
Build your own indoor racing air gates or pylons. Just print out the base parts, one or more connectors, and buy some 1/2" pipe insulation from your local home improvement store. You can use a string to keep the gate feet together. Optionally you can...
thingiverse
I've got these neat micro quads all set up for FPV that I've been flying around the house. I wanted to "add" to the enjoyment, so... I jumped into Blender and drew up some connectors to fit some el cheapo, sub 3 buck, 7.3mm diameter Wally World...
prusaprinters
Build your own indoor racing air gates or pylons. Just print out the base parts, one or more connectors, and buy some 1/2" pipe insulation from your local home improvement store.</p> <p>You can use a string to keep the gate feet together. Optionally...
thingiverse
Mini quad frame in openscad, a couple of parameters you can set for motor body diameter and prop length to auto adjust spacing. ... To do - create battery plate
thingiverse
Frame mini quad for 7mmx20mm engines 4mm carbon tubes The wire passes through the motor inside the carbon tube I hope you enjoy
cults3d
This mini quad format 130, chassis in stl and dxf version. ... Video: https://youtu.be/VCqCdpjaP7Q The main chassis is 33% PLA The hull is 20% TPU
thingiverse
Ce mini quad format 130, châssis en version stl et dxf. ... Vidéo : https://youtu.be/VCqCdpjaP7Q Le châssis principal est en PLA en 33% La coque est en TPU en 20%
thingiverse
3D printable mini quad concept. Not tested yet. The landing gear was intended to be printed in a transparent material and the little feet in TPU for some damping. Designed for 12 x 12 mm mount spacing motors with 5030 props or similar. ... - FC...
thingiverse
mini Quad sized like a Hubsan printed in 0.3 u can use Hubsan Motors (8,5mm) i used this one http://www.banggood.com/Chaoli-CL-820-8_5x20mm-Coreless-Motor-for-90mm-150mm-DIY-Micro-FPV-RC-Quadcopter-Frame-p-1054803.html Hubsan FC or a 32 bit FC for...
thingiverse
This is my first attempt at trying to create a FPV 5in racing quad. It's for a standard size racing quad 5-inch props. The base frame is 6 mm thick and the top is only 3 mm. ...Instructions and parts might change it's still a work in progress,