mini universal 3d models

This mini universal joint is attached to ball bearings.

I decided the mini universal rover wheel would allow me to design and test before I port it over to the larger wheel assembly. I've made a few alterations that should reduce some of the cost. This is earlier in the development cycle than I usually...

NOTE: nozzles smaller then 0.1mm is requierd small universal joint v1 and v2 you need 2 arms and one time the main body for a complete build V1: made for 1mm axis 2 pieces of 1mm x 5.4mm wire/rod needed V2: made for 2mm axis 2pieces of 1mm wire/rod...

NOTE: nozzles smaller then 0.1mm is requierd ANOTHER NOTE: because of the (shitty) design it wont really work well :/ small universal joint v1 and v2 you need 2 arms and one time the main body for a complete build V1: made for 1mm axis 2 pieces of...

Here is a Version of a mini Spoolholder. This Version is for Bearings. This Version is for M5x20 or M5x25 Screws (mine are to long with 30mm :D ). The Size of the Bearings are: Diameter: 16mm / thickness: 5mm / Hole-Diameter: 6mm (M5 Screws). I...

Kossel Mini universal filament spool holder with an baring( NSK (6005h2)

Kossel Mini universal filament spool holder with an baring( NSK (6005h2)

... the UP Mini. ...Takes Genuine 700g spools and also the 1kg spools available from many suppliers. Instructions Print it out and clip it on to your UP Mini! ...- You may want to spin it around to a better orientation in the UP software before printing

It can be used is small power transmission, bore diameter 7mm.

A universal backplate adapter takes the place of the plastic wall this mounts to, and makes it possible to mount this directly on any motor, so it's a universal extruder. Material required: - 3 M3x? screws for top and bottom corner (fill in...

Housing for a compact, portable XYS3580 universal laboratory power supply. The XYS3580 is an elegantly designed laboratory power supply module which can operate as a DC-DC boost converter in CC and CV mode. With an input voltage of 6 - 30 V, a...

no support required Printed on DIY T800 https://www.youtube.com/watch?v=QEvNMtPV8Ww

A combination of several other tripod designs to make the tripod the most flexible and adjustable, while remaining stable.

... change its size and the holes that hold the servo. ... for holding the mini servo in its place you will need scrows and nuts. i've used two small scrows (2mm/0.07inch) and two big scrows(3mm/0.11inch) for connecting your mini servo for somthing else.

... to Standoff: 19mm • Standoff height: 22mm • Weight: 2.7g Don't have 3D printer? Buy here https://wizz.store/products/wizz-mini-racer-universal-nano-camera-mount Support us, any amount are welcome❤️ USD$ ☕ https://www.buymeacoffee.com/wizzfpv

Printed this to support my iPod mini for the universal dock form apple but it can works for any 30pin docking station

I like to have a sleeve for my FPV-Drones so it's way easier to swap them. ...Since I couldnt find any universal Sleeves for the GoPro 11 Mini, I decided to make one myown. ...As simple as possible and not perfect at all but it works.

The Mini's stock spool holder is hard edged and jerks the filament when it's rolling. This creates excess vibration and resistance on the extruder gear, as well as being kind of noisy. This little 30-minute print fixes it in the simplest way...

Print with supports and 15% infill

Customized version of https://www.thingiverse.com/thing:2996786 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2996786

Hobby mini-formit-universal-sheet-metal-machine-Abkant-Makas-Silindri Bükme

Mini and universal support for 8mm bar the hole is 22mm, designed for ball bearings 608zz Material: PLA

Basically this is a remix that allows you to put in filament spools of different widths onto the Monoprice Maker Select Mini's spool rack. This uses standard 608zz bearings. I've also added a little guide change to keep the filament spool on the...

I searched for a good while for a suitable, general case for my WEMOS D1 mini boards. After many tries, none fit or was suitable for my application. So I decided to design one on my own. Please print the case alone and check if your board fits.

... or if you wanted to adjust the cooling nozzle. Good luck. Looking to print in ABS? Try this version instead: http://www.thingiverse.com/thing:1688282 Print Settings Printer: Monoprice Select Mini Rafts: No Supports: No Resolution: .2 mm Infill: 20

Prusa Mini Base - Universal Mount/Camera Mount/LED …Die Halterung besteht aus mehreren Komponenten, die einfach miteinander verschraubt werden können.Q: Warum mehrere Teile?A: Aus Gründen der Flexibilität und Materialersparnis.  1. der USB...

Friend needed a miniature u joint for project,actually 7. $8 bucks each at the local hobby shop they only had 3.... or wait for the shipping. ... Couldn't find any small enough already published.

Removed unnecessary plastic for faster printing , primarily used for systems that use bottom mounting

A universal bracket for the prusa mini. Ideal for my ESP 32 Cam but possible for any other device due to the simple connection.</p> <p>Srews: M2x12 M3x4 M3x8 M3x20<br/> Nuts: M3 M2<br/> Waschers: M3 (optional)</p> <p>The joint is available in two...