miniature holder 3d models
386005 3d models found related to miniature holder.thingiverse
This is yet another miniature holder. It was based on an existing design, which I am now unable to find again. It used a metal wire part which I did not have, so I made an all-plastic version with some modifications. To create a holder, print either...
thingiverse
I Just added the Mk2 variants, which have more holes for pinned miniatures and a slightly nobbled upper surface as a result, which should be even better at holding the blue tack. Free licence for non commercial use (If you want to print them and...
prusaprinters
The weight helps prevent them being accidentally knocked over, and keeps the centre of balance in your fingers. The top is grooved to help it hold blue tack, and the centre hole is deep to hold a pin for miniatures painted before basing. I Just added...
thingiverse
This is what I made to put my miniatures on while I paint them. it's also a good place to dab off excess paint. no more need to use your fingernail or the back of your hand. use any kind of yellow tack to hold mini to base. I printed this laying...
thingiverse
Magnet slots so the model can sit on the holder otherwise bluetack can work as well or rubber band through the holes if you are innovative ;). Comes with a base stand so the handle can slide in and not fall over. Also made it so the handles on...
thingiverse
https://youtu.be/hO2b2ese7YA #Pintando Miniaturas painting handle This handle was inspired by the project from [NakedFury](https://www.thingiverse.com/nakedfury/designs) handle and uses the same "horns"...
cults3d
https://youtu.be/hO2b2ese7YA #Pintando Miniaturas painting handle This handle was inspired by the project from NakedFury (https://www.thingiverse.com/nakedfury/designs) handle and uses the same "horns"...
thingiverse
Secure your miniatures without tape! ... Glue or screw this miniature holder onto any sort of peg, holder, etc for maximum convenience Derived fromhttp://www.thingiverse.com/thing:79631
thingiverse
Two basic miniature holders for painting. These holders should be used with Blue Tack or poster putty. The large holder is 2" at the top and 3" at the bottom and 3" tall. The small holder in 1.5" at the top and 2" at the bottom and 2" tall. ...Either...
thingiverse
this is paper miniature holder, made for boarding games, so you can hold in the board your picture, monsters, heros, as you want to... Print Settings Printer Brand: MakerBot ...
thingiverse
This is simple miniature holder set: sticks and the base. You can use it for painting or working with miniatures or any small parts. Attach it with double-sided scotch, blu tack or simply glue it to the stick. Once done, put it in the base slot to...
thingiverse
BOM (name : qty) M5 10mm : 1 M3 9mm : 3 elastic : 1 optionnal, for finger stand (M3 9mm : 1)
thingiverse
I have made a miniature holder for the board Game RWBY: Combat Ready, to protect the miniature when I will paint it. The part is made to be store in the Expansion Box. Once the box is close, nothing move inside. You need to print 1 part A, B and...
thingiverse
Miniature holder for 25 & 40 mm bases. Cargo Container Box in https://www.thingiverse.com/thing:3691938 Files HK-A(25) and HK-B(25) seems the same file, but its not This is designed for bases of the game Infinity, because really size 25 and...
thingiverse
This is the miniature holder I made to store my Zombicide 2.0 miniatures. It holds 25 of the standard miniature bases and 4 of them fit in a box. There's a bit of variation in the miniature base sizes so they vary from tight to loose in the holder. I...
thingiverse
*Change 11-23-2019 - Added some pictures to help with assembly* This is the improved version of my previous miniature holder: https://www.thingiverse.com/thing:2491490 This one has interchangeable clamps that allows it to hold a multitude of...
cults3d
The holder length can be extended to fit more miniatures by printing more modules and connect them with the extender piece. A handle can be connected to each side for easy handling while priming. The holder uses rubberbands of around 10cm length and...
thingiverse
I needed a clip holder to apply the base color spray to my miniatures. ... With a glue drop it can be attacched to a base (plywood).
thingiverse
Print one of everything except for the bases, those you'll want to print multiples of so you can swap out miniatures for assembly line painting. I use blue poster tack to stick the mini to the bases. You'll need at least 2 of [these...
thingiverse
I've always wanted an easy way to store my miniatures without them getting broken constantly, so I designed this to hold them down by the edges of their bases. To assemble, you need an arbitrary number of '4MiniHolderTileable', that many plus one...
thingiverse
I wanted to experiment with latches and hinges, and create a case for my miniatures. This design worked very well. You can customize the lid like I did to fit whatever you would like it to be. ... The attached file does not have the V.
prusaprinters
This holder (with the diameter of the base is 40mm) is used to attach the figure when painting.
thingiverse
Miniature in picture is by MadCapMiniatures (https://www.thingiverse.com/MadCapMiniatures/about) and it is this one (https://www.thingiverse.com/thing:3029181) I just painted it up to fit my style better. ... Logo used on top is from DragonRaider8212...
thingiverse
... You'll need to print out 4 of these. The cutout for the PawnBoxBase will fit the Pawn Box plastic standees for Medium-sized creatures (a snug fit), though it'll be too small for a typical Medium-sized miniature, use the 1inchBase for those.
thingiverse
... trained in lock-picking rest assured the Heavy brickwork and magic containment circles can thwart even the most stalwart adventurer. I used the magic circle made by devonjones who deserves full credit Credit for miniatures in pictures go to mz4250
thingiverse
... ...Sometimes when I'm painting a mini, it's hard to get up under the bottom or paint around the base if the model is in a holder. This is a 25mm base with a cylinder protruding up. Use blue tack or some craft clue to hold your mini to the riser.
thingiverse
This is a small Vallejo holder I made for my paints. You can print it without supports. I printed it on normal settings in Cura 4.0 Scale it up to 108% and you can fit the minis from the Kingdom of Aros in it. ...
myminifactory
This is a small Vallejo holder I made for my paints. You can print it without supports. ...I printed it on normal settings in Cura 4.0 Scale it up to 108% and you can fit the minis from the Kingdom of Aros in it.
thingiverse
https://www.thingiverse.com/thing:2493560 I normally use old Chessex paint pots with washers glued to the tops to hold my miniatures while painting. There's a magnet glued to the base of the mini to make storing them easier, which also makes them...