minn kota ipilot 3d models
218 3d models found related to minn kota ipilot.thingiverse
This is the inner base plate for minn kota`s quickmount , I made this only to hang my ipilot trollingmotor on the wall when not in use. I will take no responsible for your settings if u want to use on the lake it`s your responsible to make it...
thingiverse
Replacement tilt lever for Minn Kota trolling motor. ...Print at 70% infill.
thingiverse
Replace the "Insert plug" part for the Minn Kota Powerdrive V2 Motor. ... Print with Flex filament with supports.
cults3d
Control your Minn-Kota steering by remote using a servo. This is for the 30-lb motor. Shaft size is 29mm Different size shafts available on request. I will be happy to answer any question about the electronics by email. ... Servo I used from...
thingiverse
The result was a cheap solution for steering a Minn Kota trolling motor with an AliExpress [60KG Servo](https://www.aliexpress.com/item/32240916087.html") For some videos see...
cults3d
Minn Kota Propeller upgrade. ...Higher pitch, 3 blades V2 upgrade: - reverse pitch added
thingiverse
This print is for the Minn Kota Edge trolling motor and works with the triple-shot Lowrance transducer bracket. Other transducers should work as well. I suggest using PETG with supports. I have tested this print on my trolling motor for a...
thingiverse
This is a topper for a Minn Kota PowerDrive that allows the it to be used on a kayak. It is made for a 1 1/8" diameter shaft and allows for a rope attachment with added leverage to pull the motor up and tilt back for storage from the seat of the...
thingiverse
Steering bracket made for Minn Kota. ...Tested on Minn Kota 36lb and it works perfect. ...Print it as follows: PETG 230/ 75 temp 100% Infill Supports not required, but you can put them if you want.
thingiverse
minn kota Endura c2 30lb rudder for DIY Kayak trolling motor it may fit other trolling motor brand with 1 1/8" Shaft printing filament PETG / ABS - ASA / PC infill: honeycomb at 20% print it vertical as its standing up with plate supports
thingiverse
Minn Kota I-pilot Remote holder i did make a video on how i designed it below https://youtu.be/yj8eCdIdlv8 please make sure to hit the like and subscribe if you got time :D hope it can helps some out can be printed in any filament just need a small...
thingiverse
Clamp (For Shaft Diameter 1.128") Used on Minn Kota Endura C2-55 5 Perimeters 100% Infill Use 2 - 1/4 Bolts. ... Hole on side for 1/4 carabiner (Snug Fit) Spacer for Harken Pulley Kit 5 Perimeters 20% Infill Harken Pulley ...
thingiverse
Control your Minn-Kota steering by remote using a servo. This is for the 30-lb motor. Shaft size is 29mm Different size shafts available on request. I will be happy to answer any question about the electronics by email. Servo I used from...
grabcad
FDM/FFF 3D Printable shroud for a Minn Kota Endura Max 55 thruster. It may fit other models as well (primary dimension is the thruster diameter). Equation-driven spline was used to generate the NACA0006 symmetric airfoil. This file is included for...
prusaprinters
minn kota Endura c2 30lb.. ...replacement title locking pin lever</p>
thingiverse
Minn Kota PowerDrive 55lbs trolling motor transportation support bracket. ...Designed for Buster L boat.
thingiverse
minn kota endura c2. ...trolling motor elbow for kayak diy print with PETG filament at 25% infill
thingiverse
Elkana contacted me with the idea of designing a trolling motor cage. I actually do not have the motor so the measurements might varies... This is my first attempt to have this cage for a motor. I used the following measurement, after confirming...
thingiverse
This is a holder for the Minn Kota i-Pilot remote. The remote also fits in updside down (see pictures). You may ask why would I want to use the i-pilot upside down? Well, that way if you press left the boat goes left when sitting in reverse...
thingiverse
This is a box I designed to fit a Minn Kota Endura C2 30lb thrust motor controller into, using m3 bolts, a Cable Gland and an XT60 Connector. ...I included a version of the box without any holes so you can do what you please.
thingiverse
This device will fit over a Minn-Kota C2 Endura 30 lb thrust trolling motor shaft and mate with the transom mount allowing for mounting a 60kg servo. The fit is tight enough that friction will hold this in place. A drop of epoxy will secure the...
thingiverse
The original Minn Kota Endura C2 50 prop got damaged. We decided to come up we a 3 blade silent but effective replacement. This is a multipart design for easy printing on small printers. The blades are sliding into the rotor head. We used the print...
thingiverse
This device will fit over a Minn-Kota C2 Endura 30 lb thrust trolling motor shaft and mate with the transom mount allowing for mounting a 60kg servo. The fit is tight enough that friction will hold this in place. A drop of epoxy will secure the...
prusaprinters
I added the Minn Kota logo for the recipient. There's a blank version as well.</p><p>I used a wide brim on the top files because I didn't want the print to fall over due to a narrow base. I also lined the top of the print parallel to the x-axis so...
thingiverse
Two various size of rail supports for Minnkota Terrova rig/shaft (33mm diameter). A snap-on claw for 25mm hand rail and the Terrova's 33mm rig. Distance between 160mm or 220mm (two separate files). Please check the actual length and compatibility...
thingiverse
Schlomorific asked me to create a higher pitch prop. So I created some and also added more blades for higher pitch. ...This is related to my previous designs for the same topic...
thingiverse
I made these off a pic I saw on the internet. They hold the transducer wires on the shaft of the tolling motor. You will need 2- 5/16-18X 1 inch bolts to attach the top piece to the power head. I printed 3 Keepers for the shaft. ...Zip ties not needed...
thingiverse
Spacer to move transducer cable away from the trolling motor shaft. This will allow the trolling motor to retract while not pinching the cable. Use #10-24 stainless hardware and zip ties. hole through the side is for a spring or bungee cord to keep...