mintyboost 3d models

This is my modification of Ladyada's excellent open source MintyBoost kit that is documented at http://www.ladyada.net/make/mintyboost. My modification consists of a custom PCB design based on the original schematic that it slightly larger than the...

A wood-machinable or printable enclosure for the MintyBoost. ...Designed to fit the Adafruit kit's dimensions, with a vacuum formed lid that slides on for access to the batteries.

See the MintyBoost kit from Adafruit here: https://www.adafruit.com/products/14 Instructions Print at 10% infill, 1 shell (total), 0.25 mm layer height. The battery holder that comes with Adafruit's MintyBoost kit won't fit perfectly with this...

Instructions Print out two of mintyboost_slide. They are symmetric and serve as both the top and bottom. Alternatively, mintyboost_slide_rep will print two of them at once. Print out one of mintycover_slanted. Order a Mintyboost here:...

... Get a battery holder that loads from the side like this one: digikey.com/product-detail/en/BC22AAW/BC22AAW-ND/66727 Assemble the MintyBoost inside of the enclosure, insert a mintycover into the track, and snap the lid into position.

Buy and assemble a MintyBoost from Adafruit: http://www.adafruit.com/products/14 (don't solder on their battery holder). Insert the Mintyboost into one side of the enclosure. Insert the battery clips around the bosses. Solder the positive and...

Custom box for the Adafruit MintyBoost USB Charger.  I love this charger but destroyed my last one by leaving the batts in too long which discharged and blew up. I added a switch to hopefully prevent this. I also wanted enough room for a USB cable...

Custom box for the Adafruit MintyBoost USB Charger: http://www.adafruit.com/products/14 I love this charger but destroyed my last one by leaving the batts in too long which discharged and blew up. I added a switch to hopefully prevent this. I also...

Here is a housing for the Adafruit MintyBoost Charger kit.http://www.adafruit.com/products/14 You can get the kit from Adafruit with above link. Print it with your 3d printer. What is unique here is that it does not require screws and nuts to...

Here is a housing for the Adafruit MintyBoost Charger kit.http://www.adafruit.com/products/14 You can get the kit from Adafruit with above link. Print it with your 3d printer. What is unique here is that it does not require screws and nuts to...

This is my single-sided PCB version of Adafruit's MintyBoost v3.0 Instructions I'm not familiar with Eagle, so I redrew the Adafruit circuit schematic and laid out the board using Fritzing. Parts list, courtesy Adafruit:...

Made my own... I aimed for a better waterproofness. My backpack isnt the dryest place to be for gadjets. i use bathroom silicone for a tight seal. i also had a old Silicone USB Plug in my parts bin that fits right into the socket. ... ...

Made my own... I aimed for a better waterproofness. My backpack isnt the dryest place to be for gadjets. i use bathroom silicone for a tight seal. ...i also had a old Silicone USB Plug in my parts bin that fits right into the socket.

wanted a smaller case so i commented out the switch area and adjusted the length Currently printing so will update later printed 0.2 layer height and 2 layers on the shell, and 15% cubic infill

This adaptor was designed to not only center the MintyBoost, but to hold it solidly enough so the USB plug could be plugged in or removed without worry of bending the USB socket on the PCB. The material is standard acrylic. The bottom and top plate...

MintyBoost v3 box I spun up to take a 4xAA (2x pairs in series) Keystone aluminum battery bracket (Digikey 36-182-ND). Created a slotted lit to improve cooling. Added an LED (1.5k Resistor, across usb output) and a power button (Digikey PS1023BBLK) ...

This is a self-made casing for the Minty Boost (http://ladyada.net/make/mintyboost/index.html) Instructions Just print it :) The picture is not accurate: The walls of the casing in the STL files are actually a bit thicker to make it more stable.

Button and LED fit tightly and did not need adhesive. Added a copper RAM heatsink to the mintyboost as well to distribute heat more evenly. Print instructionsCategory: Mobile Phone Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No...

Assemble charge controller, MintyBoost, and resistor circuit board. I added auxiliary LEDs to the charge controller for charging and fully charged modes. Note that the two LEDs on the light bar share a voltage drop resistor. Use a hot glue gun to...

http://store.makerbot.com/mintyboost-kit-v3-0.html Instructions The print for the box is a bit tricky . I used support material on the box to keep the screw tab from drooping . I could not figure out how to keep the slot from drooping so i put some...

This is a makerbottable altoid tin-like enclosure for MintyBoost XL found at http://www.thingiverse.com/thing:2144 Will presumably also work for other similar devices. It's not necessary in the strict sense, but if you can't find an altoid tin you...

MintyBoost v3 box I spun up to take a 4xAA (2x pairs in series) Keystone aluminum battery bracket (Digikey 36-182-ND). Created a slotted lit to improve cooling. Added an LED (1.5k Resistor, across usb output) and a power button (Digikey...

The Raspberry Pi, TimeSquare, and MintyBoost kits are all available for a limited time in the MakerBot Store in NYC. Assemble the kits and make your own enclosures on your MakerBot. See the Rapberry Pi kit from Adafruit here:...

The TimeSquare, Raspberry Pi, and MintyBoost kits are all available for a limited time in the MakerBot Store in NYC. Assemble the kits and make your own enclosures on your MakerBot. See the TimeSquare kit from Adafruit here:...

Minty Boost V3: http://www.ladyada.net/make/mintyboost/ This project also uses OpenScad Font: http://www.thingiverse.com/thing:6820 for a text warning on the bottom of the minty boost and the title on the top. WARNING: Use this at your own risk. ...

Parts list: Large 6V 3.4W Solar Panelhttps://www.adafruit.com/products/500 Solar Lithium Ion Chargerhttps://www.adafruit.com/products/390 Lithium Ion Battery Pack 6600mAhhttps://www.adafruit.com/products/353 MintyBoost USB...

Build materials: 2 x small rubber bands 4 x NeoPixel 1/4 60 Ring (https://www.adafruit.com/products/1768) 1 x 3d printed white plastic visor 1 x portable battery-pack or MintyBoost pack 1 x micro-controller, I am using a teensy 2.0 1 x adjustable...