miter saw vacuum attachment 3d models

So I created this adapter that will fit the hose on the vacuum and the back of the miter saw. It fits tight on the hose, but a little loose on the saw which is fine for me. I will use a hose clamp to tighten it down on the saw. 5/3/21 Update: ...

Miter Saw Vacuum Adapter

A vacuum adaptor for a Bosch Miter Saw Vacuum hose: 36mm Miter saw: 41.40mm

One of my first 3D Model which connects my miter saw with my vacuum cleaner for better saw dust removal because the bag is very bad. ...You can take the measurements from the picture and see if it fits your setup.

I made this to adapt a small shop vac to my miter saw.

Adapter to hook a 2.5" shop vac vacuum hose to a Ryobi TS1345 mitre saw. ... (The actual diameter for the hose insert is ~2.25".)

Made this to connect my Dewalt Vacuum (1-7/8" hose male end) to my Dewalt DW715 (1-5/8' male). The universal adapters that I found didn't fit properly. ... This is made with a 1-degree taper on both sides.

Made to fit most DeWalt miter saws and Ridgid 1 7/8" vacuum hose. ... Exact diameter: 45mm - 42mm less than 90 degree elbow

I don't have a shop vac but my house vacuum works just fine. ... Goes from a Ryobi miter saw to a Shark floor vacuum.

This is an adapter to use with a Bosch Glide Miter Saw. It will connect to a 1 1/4" vacuum hose. ...The wall thickness is 3 mm.

Vacuum adapter for dust collection Ryobi Miter Saw (TSS102L). Works with 1 3/4" vacuum hose. I'm using the Ridgid 4 gal. model, but it'll work with others I'm sure. ...I would assume this works with the smaller Ryobi Miter Saw as well.

... I included the basic piece fitting into the Makita miter saw and the original files (SolidWorks 2017), should you want to adapt to another vacuum cleaner Edit : I thought Thingiverse could handle 3mf, which is superior to STLs, but apparently not.

This is an adapter that lets you connect your Dewalt miter saw to a shop vac. Funny how DeWalt's vacuum doesn't connect to their saw. anyway, I've included a 90 degree as well for a more compact package. ...

I needed a Vacuum Hose adapter for my Chicago Electric Miter saw and wanted to test ABS plastic on my Fabrikator Mini 3D printer. So I designed this adapter using Tinkercad and then printed it out on the Fabrikator Mini.I also coated the design using...

Wasn't able to find adapter to connect my shop vac (2" OD hose) to Dewalt DW715 Type 3 Compound Miter Saw's exhaust port (so I made one. Port was 42mm (1.656"). Fits nice, maybe a little too tight on the vacuum end. ... You might want to make it longer...

I needed a Vacuum Hose adapter for my Chicago Electric Miter saw and wanted to test ABS plastic on my Fabrikator Mini 3D printer. So I designed this adapter using Tinkercad and then printed it out on the Fabrikator Mini. I also coated the design...

SummaryI needed a Vacuum Hose adapter for my Chicago Electric Miter saw and wanted to test ABS plastic on my Fabrikator Mini 3D printer. So I designed this adapter using Tinkercad and then printed it out on the Fabrikator Mini. I also coated the...

No supports necessary. ...Fits my DeWALT D27113. Vacuum hose has ~39mm OD and 5.5mm pitch. 36mm opening for the vacuum and 40mm on the saw-side. ... Find STEP and Fusion360 files in the downloads.

I created this to collect the sawdust from my Dewalt miter saw while I was redoing my house's flooring. This works significantly better than the bag that comes with it. In order to effectively use this, you have to disconnect the rubber collectors...

Here is a vacuum attachment for the DW788 scroll saw. It is bolted to the trunion for the table with a 1/4-20 bolt. ... Glue a 1/4-20 nut into the provided recess (I used epoxy) being sure to keep the threads clear.

This thing plugs into the vacuum cleaner port on a Dremel 4" saw and adapts to a shopvac hose.

Fits my DeWALT D27113. Vacuum hose has ~39mm OD and 5.5mm pitch. 36mm opening for the vacuum and 40mm on the saw-side. Find STEP and Fusion360 files in the downloads. Testlink:...

This is a remix I did for dust collection on my DeWalt DW715 miter saw. I'm sure it fits many other models. If you have any luck with it on a different model, please post. Customized version of http://www.thingiverse.com/thing:560647 Created with...

This attachment allows you to connect your workshop vacuum cleaner to two dust collection units on your table saw. ... Instructions The following printer settings are for the Ultimaker² with PLA: Layer...

I duct taped it to the saw as it will live there permanently and my vacuum hose slides in and doesn't slip out - so fit is just nice. I added a little extra flare on the top of this to increase my contact area with the printer table as an 1/8"...

Designed to connect a Ridgid wet/dry vacuum that connects to 1-7/8" accessories with a Metabo C10FCGSM miter saw's dust port. The end that has an OD of 2.0 is slightly too small. Had to wrap with duct tape to make it stick in the miter saw. ...

Added more options for dimensions to vacuum adapter created by other user. ... Turns out that the 1-7/8" Ridgid vacuum hose is more like 1-13/16", and my Metabo miter saw seems to accept ~2-1/16" or 2-1/8" hoses. ...Trying to get the dimensions correct.

Customized version of http://www.thingiverse.com/thing:1285949 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1285949

Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651

Miter Saw