mk modular switches 3d models
107633 3d models found related to mk modular switches.grabcad
MK Grid Plus Modular Switch - K4882 (front only). Designed to look as realistic as possible. Use the center mark to position in a modular plate (see my library). I have included the cut-out to be used to create new grid plates to fit this switch.
grabcad
MK Grid Plus 2 Gang Modular Switch (4 Module) - K24334 (front only). Designed to look as realistic as possible. Use the screw holes to find the center and position flat to a wall. Since this is a modular switch, the switches can be removed /...
thingiverse
These are designed to be two part replacements for the hat switches on the Logitech/Saitek X56. Print the stem in transparent PETG with a raft transmit the RGB lighting better than stock. Then print the caps in TPU and press fit them on. If you play...
thingiverse
This is a remix of my Fish Ladder Mk.3 (https://www.thingiverse.com/thing:4828205) The only difference is the index finger columns TGB and YHN were moved up a notch. Otherwise it the same board using spring-swapped Matias switches. ...
thingiverse
UPD2: a bit of re-work: - added a version of the top plate "Plate Wells" that holds the switches better. - added a version of the bottom part that is (a) using mini-usb instead of USB-A, (b) having the audio connector and the reset button holes on...
thingiverse
Key cap guard/border added for looks mostly, but also may help protecting the switches from being pulled out accidentally. ... Fusion 360 project: https://a360.co/3ac2tSX UPDATE 20211122: Added a slightly modified version - cut in some places the...
thingiverse
A remix of my Fish Ladder Mk.3 keyboard (https://www.thingiverse.com/thing:4828205) to use Kailh Choc switches. I swapped the springs to 12gf and removed the stabilizers from them. The switches are holding in holes by friction only. Keyboard is...
thingiverse
A special feature is it's extreme modular construction that will allow not only easy upgrades like other Motherboard, LCD or different mechanical components but also a quick-swap system that allows you to change Hot-Ends within just a minute to...
cults3d
New prototype chassis for the new generation Rhino MK XIX multi-purpose vehicle, straight from Martian forges. Due to the fact that this is a prototype, please expect some minor changes and new versions of the modules in the future. The assumption...
thingiverse
I noticed that there were very few prints that was designed to fit a full playing card deck, and be modular to account for an infinite amount of decks displayed. I will be working on a design without the 3 extrusions, so that it will look like a...
thingiverse
Modular, hexagonal shelf and drawer design I made with a double-dovetail interlocking pattern. You can mount one module wherever you want, and then slot in a couple others without need for extra screws every time. Includes files for different...
thingiverse
The TEMPO is designed as a modular wall/bench mounted organizer, and can be used in different configurations (modules will be added over time). the modules have holes for screws to mount to the wall/bench and dovetails to connect to each other. ... ...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=1955876 Instructions Using the following options: name = MK letter_font = Fontdiner Swanky ring_offset = 1.5 letter_spacing = 0.75 ring_thickness = 3 ring_diameter = 3 keychain_thickness = 4
prusaprinters
The switch hole mount size is 19mm x 12.6mm to allow for larger rocker style switch. The holes were designed to fit these rocker switches. ...<a...
thingiverse
A 3d printable sprue holder, designed to be expandable. It's designed to be printed with little to no supports. ...Able to hold most standard model sprues.
thingiverse
Arduino Project With Modular Case with 1602 Display, Sensors, Switches, LEDs, USB & Power
prusaprinters
You will need the center module posted below to use with this, they can be found at the link below: https://www.thingiverse.com/thing:3690500 I printed an earlier version of this model which needed improvements for mounting the switch., which I have...
thingiverse
You will need the center module posted below to use with this, they can be found at the link below: https://www.thingiverse.com/thing:3690500 I printed an earlier version of this model which needed improvements for mounting the switch., which I have...
thingiverse
The switch PCB is mounted in the new case using three M3x6mm plastic standoffs (male-female version), three M3x8 button head screws and three M3 plastic nuts for the standoffs. ...The back cover is designed for the four original case screws of the...
prusaprinters
Remix for an Edimax ES5500M 5-port Gigabit switch. The ES5500M has an odd plastic case and a power connector on the front. This mount is designed to replace the original plastic case completely. You can still power it from the front or just solder a...
thingiverse
After installing Philips Hue Lighting I needed something to stop the habit of switching off lights at the wall, so here's a simple cover designed to fit over the rocker on a MK Light Switch (may fit others). ... Print top side on bed (as shown).
thingiverse
This was designed to fit a switch with the following dimensions: 150 x 97 x 28mm There is a 1mm clearance added to the above dimensions, so the opening is 151x29mm. The switch can be mounted with double sided tape. This is untested, but if it is...
thingiverse
So if you need to mount a Netgear switch, I posted a remix that uses M3 screws which should slide in the mounting slots on the base of the switch without a problem (but since filament don't grow on trees, it is not tested)....
prusaprinters
So if you need to mount a Netgear switch, I posted a remix (link below) that uses M3 screws which should slide in the mounting slots on the base of the switch without a problem. Thanks to the make by DasFasty for testing the M3 version!...
thingiverse
This is a replacement knob for a MK dimmer switch. My original ones were white and beginning to look a bit jaded. ...These would look good in any colour I guess :) See pictures for settings, maybe not the best but they worked for me...