mk10 extruder 3d models

Nozzle 0.4, layer 0.12 This adapter allow owners of MK10 extruder (like the Titan on Tevo Tornado) to use a M6 PTFE, like the capricon one photo.

MK10 Extruder V5 bowden 30x30 fan 40x40x20 blower fan x carriage aşağıdaki adresteki ile uyumludur. https://www.thingiverse.com/thing:2514659 (JackWaterfall) https://youtu.be/PxwTfdZVeAI Bu tasarım için 42x42x20 nema motor daha iyi olurdu. ...

Nozzle 0.4, layer 0.12 This adapter allow owners of MK10 extruder (like the Titan on Tevo Tornado) to use a M6 PTFE, like the capricon one photo.

These should work for all printers using the stock MK10 extruder heatsink and fan. ...Print Settings Printer: Qidi Tech X-One Rafts: ...

Flex MOD MK10 Extruder frame this was someone else's work that i have modified to allow for a 4mm OD PTFE tube to be inserted between the frame and the thermal break to stop flexible filament binding Update to Ver4 more clearance for Extruder Gear...

Common mk8/mk10 extruder often has similar problem, unable to use flex filament, fixed spring tension and teflon tube has some backlash for when using festos. This one can use either M4 nut to secure the teflon tubes in the input and ouput as well...

This is a more natural looking version of the CR-10 FU knob. ...It is also easier to print since it doesn't have the abrupt transision at the wrist. Fits perfect on MK10 Type extruders like CR-10/Ender-2/3

Most MK8/MK10 based extruder unit share similar problem, the bigger part is a single piece and what if you screwed up ended up buying an extruder unit but the orientation were wrong? The idea for this is to solve Left/Right hand orientation of the...

I find if you press the lever to hard you leave a small gap for the filament to leave the extruder from under the roller and if you keep pushing the filament after the resistance you will see the filament come out the side of the extruder under the...

This is a heavily reinforced extruder arm and body. It is designed to be easier to print, and has removed the narrow point just above the idler pulley to to distribute stress better. Goals were to: 1) Verify dimensional accuracy. 2) Beef up the...

This is a heavily reinforced extruder arm and body. It is designed to be easier to print, and has removed the narrow point just above the idler pulley to to distribute stress better. Goals were to: 1) Verify dimensional accuracy. 2) Beef up the...

e3d v6 hotend mount for mk10 extruder. BOM: 2X M3x25 socket head cap screw 1X e3d v6 hotend Note: I had M3x30 screws instead of M3x25 so had to place one more excessive (mk10_e3d_ct) part to screw tightly. ...Final design is not that bulky

I guess this will work for other extruders of similar design if they use the same size spring, but I only have experience with the MK10. Print Settings Resolution: 0.1 - 0.2 ...

An omnidirectional / toroidal vane cooler for the MK10 extruder module of the ReDuplicator i3 MK3x: https://www.thingiverse.com/thing:2686588 The goal was to provide airflow from all sides, vs. the back-heavy cooling of the cooling ducts that are...

This little mod sits in place of the steppers on a mk10 dual extruder's heat block, and It may work on a mk10 single. All you have to do is tap the hole for the m10 push fit and you're good to go. I'd reccomend printing it at 50% infill or higher...

Prusa type radial fan (50mm) holder for MK10 extruder. Doesn't require additional HW (bolts or nuts) Chassis will be fasten with the extruder fan bolt (remove the 10mm nylon pipe). Additional support is given by the edge of aluminum extruder bracket....

Prusa type radial fan (50mm) holder for MK10 extruder. Doesn't require additional HW (bolts or nuts) Chassis will be fasten with the extruder fan bolt (remove the 10mm nylon pipe). Additional support is given by the edge of aluminum extruder bracket....

After upgrading my Tronxy P802MA with a Mk10 extruder upgrade from AliExpress (found here https://www.aliexpress.com/item/32808614857.html) I added a MicroSwiss all metal hot end and throat. Only problem was the heat soak so I needed to cool the...

So I designed one from scratch based off the stock MK10 extruder that came with my plus. Alignment and thickness are correct and I've raised the spring nipple plate up 1.5mm for increased tension. Install is fairly simple. Cut a 4mm piece of PTFE...

Hi, this is all in one system to cooling extruder mk10 and the print piece. I think it's useful also for other printers who use mk10. I called it "scolopendra" because it looks like a scolopendra head :) More info on all Scolopendra...

Hi, this is all in one system to cooling extruder mk10 and the print piece. I think it's useful also for other printers who use mk10. I called it "scolopendra" because it looks like a scolopendra head :) More info on all Scolopendra...

A spacer for the i3 / MK10 hot end cooling fan that won't fall out when you re-assemble. It replaces the two cylinders. It has a connecting bar that slips between the bottom two cooling fins. I updated with 4 sizes. ...Print Settings Printer Brand: ...

A spacer for the i3 / MK10 hot end cooling fan that won't fall out when you re-assemble.It replaces the two cylinders. ...It has a connecting bar that slips between the bottom two cooling...

... so I went to this dual gear extruder here. Much better print quality by switching to this but the extruder is thicker and so things had to be adjusted. No multi-part pieces. Just print the thing as one piece at 20 percent. Seemed plenty stiff.

To enable reliable TPU printing with the Mk9 extruder, I designed a new frame/housing/feeder with less open space around the extruder gear and guide wheel, below the point where filament is being fed/pushed, so the gap is too small for filament to...

CTC Prusa I3 Pro B MK10 Extruder Plate for Quick fit Mine printer has a large L shaped aluminium plate that didn't fit in the other Quick fit plates I saw. So I made a simple generic plate designed to provide good support. ... I plan to drill a...

So far best MK10/MK8 extruder bracket. It can handle 40D flex with 60mm/s or more speeds. It has spring tension regulation also. I do recommend printing with slight over extrusion, it does help with parts strength. Might need some teflon tape to...

MK10 dual extruder PTFE cutting jig Flashforge, CTC I made this, as there are a couple of other tools about on thingiverse that aren't the correct size. I found using the other versions the nozzle would consistently leak. ... This tool has been made by...

Fixed a problem with the original STL file, and improved the resolution.

DaVinci MK10 filament guide (Filamentführung):Printer:Wanhao Duplicator 4S - Steel ExoFrame (2xMicro Swiss MK10 All M​etal Hotend)Rafts:NoSupports:NoResolution:0.2mmInfill:100%Material:ABSDaVinci MK10 cooling block (Kuehlblock):CNC milled from solid...