mk7 golf dash cam 3d models
30041 3d models found related to mk7 golf dash cam.thingiverse
This is a Yamaha golf cart mount for a Rove R2-4D dash cam. The mount attaches to the 3/4" rod that supports the center rear view mirror. A 12v to 5v buck converter is connected to the 12v on the ignition switch and provides power to the dash cam.
cults3d
VW Golf mk7-7.5 air vent dash base pod gauges DUAL GAUGES 2 halls for 52mm gauges STL files * case pod dual gauge (stl) * dash base (stl) very good quality like a aftermarket Looks awesome I would like to see your photos, with the prints you made at...
cults3d
VW Golf mk7-7.5 air vent dash base pod gauges DUAL GAUGES 2 halls for gauges 62mm but you can use 60mm with tape! You can use 52mm if you print the adaptor for 52mm gauge STL files * pod gauge dual (stl) * dash base (stl) * back plate part 1 (stl) *...
cults3d
We are proud to present our own sideview/silhuete of an Volkswagen Golf mk7 sideview/silhuete keychain We keep our standards size under 8cm x 4cm x 4mm ".stl" file for the experienced user to slice it the way you what it Truly tested and printed from...
thingiverse
Designed for VW GOLF MK7. ... Parts: ELM327 (no need bluetooth or wifi version) 2.0 inch ST7789 IPS Display Arduino nano (any 328p) TTP223 Touch Key (for menu) LDR (for autobrightness function) 6 x 220 ohm resistor Software: ...
thingiverse
Turns out it fits just fine in my Mk7 Golf R. I remixed it to use aTechMatte magnetic phone holder. I ended up using an M3X15 screw cap hex with a 5.45mm head on it. If you use anything shorter it might not reach the threaded mount.<p> <p>As...
thingiverse
After installing a RaceChip tuning box in my MK7.5 Golf I needed a good way to mount this external control unit - so I made this mounting plate. With the included clips and zippers you can mount the RaceChip next to the front lights. I recommend...
thingiverse
A remixed print-and-play clutch stop for my 2018 VW Golf R. I am used to a quicker engagement off the floor, so this clutch stop solved most of the excess pedal travel problem for me. Just print this out, put your original rubber stopper in the hole...
prusaprinters
Got tired of the cam constantly falling down as no sticky tape/pad would stick to the plastic cover on the boot lid “roof”.In the end I decided to make a simple mount that hooks on the plastic cover and keeps the camera in place.Printed with PETG to...
thingiverse
I designed a dash cam support to be mounted on the inside mirror. ... i used the ball joint and the nut from the dash cam parts.
cults3d
Cults Special Edition of PROVENTCUSTOMS Products For Volkswagen GOLF MK7 AND MK7.5 SUİTABLE For 52mm Gauge Tight Fitting
thingiverse
This is a boost gauge vent pod designed for a mk7 / mk7.5 Volkswagen Golf GTI. I included two ways of printing this: in one piece or in parts. ... I printed mine in parts to make printing in ABS simpler.
thingiverse
I needed a mount for my dash cam because the suction cup was messing up my windshield tint. I would print this out of PETG or similar due to the heat. PLA+ works but gets very soft. ...I used 3M double sided automotive tape to mount it.
grabcad
This clip allows you to mount a dash cam to the passenger sun visor. You will require an M5 20mm cap head bolt, washer and nyloc nut. The nut in the picture was machined for the purpose, note the camera fitting is tapped M5 so the cap head bolt is...
thingiverse
Link For Dash Cam Kit I Used: https://www.amazon.com/gp/product/B07DGS11CM/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 Link for Mirror Mounting Bracket:...
thingiverse
The dash cam I printed these for uses a Mini USB cable, which is a bit thicker in size than most Micro USB cables. If your dash cam uses Micro USB cabling or any other type that is not the same size as mine, you may want to scale this print down a...
thingiverse
These are meant to sit on your dash and face sideways, to help you see around corners for traffic. The camera mount was designed to fit in the corner of the dash against the windshield of my 2000 s-10. I made these out of abs and have 1 of them...
thingiverse
- Xiaomi Yi Smart Dash Camera mount - Didn't want to remove original mount from my car when I traveled abroad and wanted to use the camera in rented vehicle... ... - Printed in PETG, 236C, 100%infill, 25% fans - Use thick, double sided tape to stick it...
thingiverse
This bracket is a better design for the SJ1000 Dash Camera that allows you to see the screen through the bracket. Instructions Print with support. ... Remove the Plastic camera holder from the belt...
thingiverse
This is a mount for a standard, cheap [yi cam](https://smile.amazon.com/dp/B01CW4ASS0) Simply wedge this up by your rear-view mirror and run a long [usb cable](https://smile.amazon.com/dp/B073PT6Q1P) around your windshield
thingiverse
My holder for the cam broke, printed a replacement mount with petg but the sun melted and deformed the piece. So made this to hold in place even with sun exposure. You have to cut the holder of the original holder. ...Mine was already broken so had no...
thingiverse
A tray to hold a OnePlus 8 (without case) in the cubby of a MK7/7.5 Golf/GTI/Golf R.
prusaprinters
For mounting a RVC-High camera in a RVC-Low mount on a VW Golf Mk7e.g. ...Camera 5Q0980568B</p>
cgtrader
Highly detailed Golf GTI Mk7 with interior, breaks detail and clean topology Easy to work with, ready to import into your scene
cgtrader
Highly detailed Golf GTI Mk7 with interior, breaks detail and clean topology Easy to work with, ready to import into your scene
thingiverse
Custom holders for WS2812 RGB LED modules as a replacement for OEM daytime running lights boards in VW Golf MK7 with bi-xenon headlights. Not road legal. ...Do it at your own risk.