mks base 3d models
370061 3d models found related to mks base.thingiverse
MKS Base Controller Stand Print Settings Printer: Tevo Tarantula Supports: Yes
thingiverse
Case for MKS Base board on P3Steel printer. Mounts on the left (as seen from the front) PETG or ABS recommended. ... OpenSCAD source included
thingiverse
MKS Base case I made since all of the ones on Thingiverse were awful. ...Has a hinged lid for a 50mm fan.
prusaprinters
Case for MKS Base board on P3Steel printer. ...Mounts on the left (as seen from the front)</p> <p>PETG or ABS recommended.</p> <p>OpenSCAD source included</p> Category: 3D Printer Parts
thingiverse
This is a case specially designed for MKS BASE Motherboard. Convenient for installation and fixing of various printers. Simple and beautiful. ...Just use 3d printing and you can make it.
thingiverse
I have a 3D printer which uses a MKS Base v1.1 arduino PCB, i used to have small plastic Standoffs that were fiddly to hold, and fit so I came up with this. ... It hold all the standoffs together making fitting so much easier.
sketchfab
This is a mount for the MKS Base mother board with integrated motor controls. I designed it for a side mount (2020 extrusion) for the inside or outside of a Delta style printer. I built an large scale Delta printer so I was able to mount this...
thingiverse
I made this specially for upgrading my Tronxy X1 to a dual extrusion printer with a MKS Base V1.6 controller board, but I think this should also be backward compatible with V1.5, 1.4 and so on. Bottom case: You need M3 screws of 5-6mm lengths to...
grabcad
Carte de contrôle MKS Base V1.5 pour imprimante 3D ou autre machines CN.Certains composants ne sont pas présents pour éviter de trop alourdir le fichier.MKS BASE V1.5 control board for 3d printer or for any other CN machines. ...Some components are not...
thingiverse
A Model of the MKS Base V1.5 board from Makerbase for designing mounts and enclosures.
thingiverse
Version 2 now, alter side vents, mounting points, 2 fans on lid. ... MKS Base box & lid, extra large so you can run extra wiring, also mount to 3030 upright T Slot Aluminium.
cults3d
This is for mounting an MKS-Base control board to the side of an ATX PSU. You can then clip most of the wires short, and feed out just enough to connect power. ... It has integral support - just use a razor to pop it off.
thingiverse
This is for mounting an MKS-Base control board to the side of an ATX PSU. You can then clip most of the wires short, and feed out just enough to connect power. ... It has integral support - just use a razor to pop it off.
thingiverse
What you'll need: 1 x printed MKS Base mount (from above file) 6 x M2x16 screws & nuts 1 x MKS Base board (preferably v1.4 or v1.5) 1 x RepRap Discount Smart Controller (optional) 1 x MKS Base TFT (optional) 1 x 12V/24V fan (optional) 2 x XH2.54 2...
thingiverse
I am using an MKS Base V1.3 board with a 3.2" TFT Display on my ReP_AL CORE XY printers. Heres an enclosure designed to fit on the Alu frame. ... Link to the ReP_AL CORE XY Printers: https://www.thingiverse.com/thing:3134290 ...
thingiverse
For those of you recycling old printer parts during their Voron build (like me), here is a case for the MKS Base controller board. I based this design off of a file I found on the internet. I measured the dimensions with my calipers and they seem to...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=351092 Made so I can mount my mks base with double sided tape inside my wanhao i33 duplicator metal case with a mosfet board and not need to drill new holes. As it's a tight fit I needed to...
thingiverse
I wanted to move the mks board out of the way a bit and I like the 90deg mount I've seen other people with but wanted to be able to see the lights on the board a little better also. ...Print Settings Printer: Tevo Tarantula i3 ...
pinshape
Basic cover for the MKS TFT32 touch screen. There are 2 holes in the rear side to screw a support to your 3d printer. Required: Bolts DIN912 M3x20 // 4 units Nuts DIN934 M3 // 6 units Attached Solidworks files. Supports are not...
thingiverse
Basic cover for the MKS TFT32 touch screen. There are 2 holes in the rear side to screw a support to your 3d printer. Required: Bolts DIN912 M3x20 // 4 units Nuts DIN934 M3 // 6 units Attached Solidworks files. Print Settings Printer: ...
prusaprinters
I wanted to move the mks board out of the way a bit and I like the 90deg mount I've seen other people with but wanted to be able to see the lights on the board a little better also. Print instructionsCategory: 3D Printer Accessories Print Settings...
thingiverse
This is a housing I designed to fit my MKS Base and MKS-TFT28 along with a mosfet for the heatbed to sit next to my Delta for easy control and wiring. For the back plate I designed 2 versions. One where the cables just run trough the back plate...
thingiverse
So, you currently have an Arduino-based MKS-BASE V1.3 control board (or other 100x80mm board) on your hictop (or other) brand 3D printer? Does that got you down? Does 32 bit processing and 1/32 micro-stepping get you excited? Don't you wish you could...
prusaprinters
This is the casing designed for MKS Base by MKS itself. ...I've downloaded it from their Chinese support group on QQ messenger.</p> Category: 3D Printing
thingiverse
This is the casing designed for MKS Base by MKS itself. ...I've downloaded it from their Chinese support group on QQ messenger.