mks base v1 3 3d models

With this mod I have adapted the TFT32 screen to the Ender 3 printer so that we keep the two screens and fully functional (just connect the old screen on the EXP1 connection of the MKS GEN L by turning the connector before cutting the small slot and...

Fits any machine with a MKS v1.1 board perfectly but was incredibly useful on my Sunhokey Prusa i3. I'd knocked the back of my hand a few times against various pins on the control board during filament changes, making it essential to have some kind...

Basically, it's a support for the MKS MOSFET V1.0 with four stands that have little slots in them to keep a standard PC 80 mm fan in place. You'll need to drill four holes if you want to screw the board like I did. My printer setup is quite bad, so...

great upgrade for an ender3 MKS Robin nano v3 available now I did this for v2 not sure about the changes on the board dimensions I dont think there are any case fan 60x60 Silent fan (Noctua/gelid) hot end fan 40x40 stock Ender 3 fan / v6 fan cooling...

This is a crucial application for the MKS Gen L Board upgrade on your Ender 3. The mainboard fan must be installed from the outside due to the stepper drivers' presence. Strategically, the fan hole positions the fan to cool the stepper drivers...

This is a detailed guide for the MKS Gen L case of Ender 3. When assembling, use M3 screws exclusively. If you'd like to suggest improvements, feel free to leave comments below. Consider showing your appreciation by donating an amount of your choice...

mounting case for the MKS PWC 3.0 Print Settings Printer: BIQU B1 Rafts: NoSupports: No Resolution: 0.16Infill: 25% Filament: filastore PETG Category: 3D Printer Accessories

Version for MKS Gen L 15/05/2021: Add the top with 80mm vent

When installing an MKS GEN L board with an MKS TFT32 v.4.0 screen, we risk losing some operating characteristics from the machine itself if we remove the original screen. These include changing steps and jerks. With this mod, I've adapted the TFT32...

W3D_MKS_Base_Side_Mount for the Tevo Tarantula And W3D_MKS_Gen_L_Side_Mount for the Tevo Tarantula Print Settings Printer Brand: TEVO Printer: Tarantula Rafts: No Supports: No Resolution: 0.2 millimeters Infill: 30 percent

This a remix to fit the Makerbase MKS Skipr to an Ender 3 PRO with mounting for mosfet and relay module. - UPDATE 1.1 Dropped enclosure down 2 mm to make clearance for x axis driver. Modified Right Lid to make easier to print Added...

This Case is for the MKS TFT32 3.2" Touch Screen. I currently use it with my Folger Tech FT-5. I Printed mine in TPU and PLA. Front Panel is made of TPU Back Panel is printed with PLA for extra rigidity. It has SD card access and USB access...

This mount is specifically designed for the MKS TFT 32 touch screen, and it's intended to be mounted on the left-hand side of the Ender 3. However, I still want to use the stock LCD panel on the right-hand side. As a result, this mount should also...

I had already swapped the stock Melzi board out for an MKS Gen L v1.0, but didn't like the mounting options available for using the stock box. So I took this opportunity to learn Fusion 360 and got inspiration from other control boxes I've seen. The...

This Ender 3 replacement mainboard case is specifically designed for the MKS SGen L (32 bit - LPC1768) board. The design is a direct remix from http://www.thingiverse.com/thing:3311643, and it requires M3 screws to assemble. Update: The necessary...

For MKS Gen V1.4 Designed for use with usual 80mm fans plus M3 screws; woodscrews also work great or even better. It can be mounted very well vertically on 2020 extrusions but can also be mounted on the ground or any baseplate just as well using M3-...

Necessity always demands creation's attention, and in this case, I'm upgrading my Tevo Tornado with an MKS GEN-L V1.0 board. To keep the drivers running smoothly, a good ventilation system is essential. After searching Thingiverse for a suitable...

Housing designed specifically to replace the standard Ender 5 casing when utilizing the MKS TFT 3.2 mm touch display is now available. This housing provides ample space for the WiFi module and allows for easy access to the SD card from the side. A...

This is the Marlin 2.0 firmware preconfigured for MKS Sbase 32-bit boards installed on stock Ender 3 printers with 1/32 microsteps enabled. The auto extruder fan operates at a temperature of 50°C, and the part cooling fan is working as expected. The...

I'll upgrade the electronics to an MKS Gen 1.4 and a TFT24, swapping out the LCD screen on my Ender3. I designed a simple mount adapter that prints easily and looks fantastic. ... Have fun!

Here's what I've got so far: * A single 40x40 fan to keep things cool * Four M3 screws for securing the display panel * Four N2.5 screws for fastening the top cover in place * Four M4 screws for mounting the MKS board securely * A power supply...

... replace RAMPS with MKS GEN L, I drew inspiration from it. Both cable outlets and the top and rear ones have a tunnel for cable ties. The file case_MKS_GEN_L_v14.f3d is a Fusion 360 archive that allows you to completely redesign the case if you wish.

some changes on the electronics enlcosure and the screen is bigger so frame needed adapting.great upgrade for an ender3 MKS Robin nano v3 available now I did this for v2 not sure about the changes on the board dimensions I dont think there are any

Changed from mightyboard to mks sbase board and upgraded the lcd to a tft touch screen .. designed the case to hide buttons .. and blanked the lcd cutout This thing was made with Tinkercad. ...Edit it online...

When installing an MKS motherboard, users must securely fasten two ribbon cables directly into designated slots on the display itself, specifically labeled as EXT1 and EXT2. ...This adjustment not only ensures a more spacious installation area but also...

some changes on the electronics enlcosure and the screen is bigger so frame needed adapting.great upgrade for an ender3 MKS Robin nano v3 available now I did this for v2 not sure about the changes on the board dimensions I dont think there are any

Two parts designed to cleanly mount a MKS Robin Nano in an FLSUN QQ-S. The case of the printer also need to be modded : - enlarge the USB cutout, - half cut one of the original PCB support. ...

I upgraded the mightyboard to an mks sbase board and swapped out the old lcd for a shiny new tft touch screen .. I crafted the case to conceal the buttons from view, then blanked out the lcd cutout to give it a sleeker look. ...This thing was designed...

The objective was to construct a case for the MKS base v1.4 and additional heatbed mosfet. An innovative feature is that no screws are required to assemble the entire case. However, if there's a dedicated plate holding your printer, you might need...

I modified it a little because of the linear rail's constraints. I added a bottom fan since I use a foot that elevates the printer. The box was designed specifically for M3 inserts. ... Fan dust filter:...