mks gen l v1 vs v2 3d models

A Cover for MKS Gen L 1.0 for a 60mm x 60mm x 10mm fan. I used 25mm M3 spacer for each hole like these: ...

Humans have created a small enclosure for the MKS GEN L board that attaches to the left side of the i3 duplicator. ... To install the Power Supply on the right, check out this custom design: https://www.thingiverse.com/thing:3438529

... ModelSmart 250S to today's standards by making a few key changes, starting with the mainboard. ...To keep it dust-free, I'll enclose the new board in a casing that fits perfectly into the original screw holes, housing the MKS Gen L board inside.

Replace MKS Gen L V 1.0 with DRV8825 drivers and a case that's perfect for coolers. ... I'm here to help, and in return, I'd love it if you could share the Marlin code with me at https://www.paypal.com/invoice/p/#9DMY8D24DLS9MTMS

A simple protective cover to shield the SD card adapter from dust for use with the mks gen l. This custom cover features four precisely aligned holes that mirror those found on the SD adapter's printed circuit board. ...To secure it firmly in place,...

MKS Gen L 1.0 PCB Cover to mount an 80mm Fan with rubber fan decouplers. The cover is elevated by 6mm, as my new stepper drivers will feature taller heatsinks. ... The rear piece boasts two 3.2mm holes for a Z-Splitter (21.5mm hole spacing).

The MKS Gen L case is designed to provide superior airflow and cooling capabilities for 2020 extrusion side mounts, featuring an integrated 60x60x10mm fan that can be upgraded to a thicker fan for increased performance. ...The fan's strategic placement...

... Out an Alternative Mosfet with Holes at 52mm x 42mm as Shown Clearly in the Attached Picture. ... This is for the MKS Gen-L Mounts, Specifically those Illustrated in the Original Source Material by Omn0mNomAgOn, Carefully Followed and Replicated Here.

Original MKS Gen L adaptor didn't fit for the Ender 5 as the PSU was in the way. Moved the mount holes and.. voilà.. Here you go. ... Rev2: The mount holes are 21mm more to the left to give the board a little more space between the frame edge and the...

Remix of Supremicus' nice MKS Gen L adapter bracket: https://www.thingiverse.com/thing:3018807 Changes I made: * Since it was prone to vibrations I reinforced the fan mount. * I also made the fan mount a little bit lower since it was in the way...

Since the Makerbase MKS Gen L motherboard has a mounting hole pitch that differs slightly from the original Tevo Tornado Mainboard, I've created this simple adapter plate to bridge the gap. The MKS Gen Board is easily rotated 90° and screwed directly...

This mounting plate enables the MKS Gen L Dual Mosfet box case to be mounted on an Anet AM8 in any orientation on the left side of the printer. The holes are strategically placed for rotation in 360 degrees, ensuring optimal clearance and alignment....

A 90-degree bracket is used to secure an MKS GEN_L and MKS MOSFET to a 2020 frame with M5 screws, the Tevo version of the MOSFET being identical in functionality. Four small standoff STLs are printed to elevate the board off the bracket. A top...

Also included is a reduced thickness cable protector to give you some extra room, as the MKS Gen L in the stock housing can be quite tight, especially if you're using barrel connectors on your terminals. This should print as three 0.4mm lines; to...

Electronics housing for MKS Gen-L and Mini LCD utilizes 3mm heat inserts. The LCD face is printed down without supports, ensuring efficient production. Heat Insert Component: McMaster-Carr part #94180A331 is utilized. LCD Employed: MKS MINI12864...

Custom Control Box for Ender 3 MKS Gen_L Upgrade Simplified, Easy Installation The stock lid of the Ender 3 printer is reused, eliminating the need to extend any wires. The control box is designed to house an MKS Gen_L board with seamless...

... To minimize dust accumulation on the drivers, I highly recommend installing both a suction fan and a blowing fan. This dual-approach strategy effectively prevents the buildup of dust, ensuring your Mks_Gen_L board runs smoothly and consistently.

Here is the rewritten text: I built a custom 3D printed case specifically designed for my Ender 3 printer, featuring the MKS GEN L board. The case is installed in the back right corner of the printer, below the power supply, with cables long enough...

This thing is a case for the MKS-GEN-L or MKS-SGEN-L-3D-printer-board. there are four different types: a.) With german text, nuts can be inserted while printing b.) Without text, nuts can be inserted while printing c.) With german text, nuts can be...

This thing is a case for the MKS-GEN-L or MKS-SGEN-L-3D-printer-board. there are four different types: a.) With german text, nuts can be inserted while printing b.) Without text, nuts can be inserted while printing c.) With german text, nuts can be...

The original MKS Gen L adaptor didn't fit for the Ender 5 because the PSU was in the way, so it needed to be modified. To solve this problem, I moved the mount holes and made some adjustments, resulting in a perfect fit. ...The revised version of the...

If you want to collaborate with me please subscribe to my YouTube channel https://www.youtube.com/c/3dmakeres even if it is not your language, it is for collaborating, you can also make a donation to my Paypal account 3dmakeres@gmail.com Adaptador...

I made a remix of my own design, a Punisher lid for the Case for MKS Gen L / RAMPS + dual MOSFET. It's available in two sizes: 80mm and 120mm. If you want a custom lid that I don't have yet, just let me know! I'll make it and post it here as soon as...

Check out this awesome adapter - the MKS Gen L to U20 Motherboard! If you're interested in teaming up with me on some amazing projects, be sure to hit that subscribe button on my YouTube channel at https://www.youtube.com/c/3dmakeres - even if your...

I upgrade my 3D printer with a new MKS GEN L motherboard today. The USB port fits perfectly into an opening in the case, leaving room for the fan to stay in its original spot. This motherboard upgrade is a huge improvement - I'm thrilled not to...

Marlin 1.1.9 specifically designed for Creality CR10-Mini My configuration, single nozzle, dual extrusion setup (color and support printing capabilities) MKS GEN L motherboard paired with five TMC2208 drivers Hotend AIO EVO module installed Touch...

This is a basic reworking of the lower part of the Daemon 3D printer, modified to accommodate an MKS Gen L board in place of the original RAMPS/Arduino MEGA setup. Note that this design obstructs the board's USB port. ...I opted not to include a notch...

In this enclosure you will have space to put your MKS GEN L(it doesent matter if it's V1, 2 or 2.1) a Raspberry Pi-3(I assume that other models could fit too), as you can see, you can put the raspberry pi in two orientations, acording to your needs...

It can be setup at the bottom of your 3D printer with two corner Joints(20*20). ... And there is enough space to hide the cable in the BOX.

MKS Gen L Adapter for Creality Ender-3 found on #Thingiverse https://www.thingiverse.com/thing:2905916 If you haven't used E1, it's recommended to stick a small strip of tape around it to improve airflow. I had the lid designed extra so that you can...