mks gen l v1 vs v2 3d models

I rewired the core circuitry to incorporate an advanced power transistor module.

Merci à Latubi pour la version original :o) J'ai ajouté la possibilité d'utiliser des attaches câbles.

Engineer optimized panel configurations to facilitate smoother cable management and reduced clutter.

I've ditched the extra horizontal mount feature altogether. ...It wasn't doing much for me anyway, and it did have a rather awkward appearance to boot.

I'm in need of a custom holder for my new SKR1.3, combined with dual Mosfet and Raspberry Pi3b. After scouring the web for a matching design, I finally found what I was looking for at https://www.thingiverse.com/thing:3463468, courtesy of neb1. The...

<p>I need a holder for my new SKR1.3 combined with dual Mosfet and Raspberry Pi3b. After looking for a matching design, i found <a href="https://www.thingiverse.com/thing:3463468">https://www.thingiverse.com/thing:3463468</a> from neb1.</p> <p>The...

<p>Customized version of <a href="https://www.thingiverse.com/thing:166045">https://www.thingiverse.com/thing:166045</a></p> <p>Created with Customizer! ...<a...

This is an adapter to mount the MKS Gen V1.4 board into the original Wanhao Duplicator i3 control box. It also has mounting points for a MOSFET with 52mmx42mm hole spacing such as the BIQU. It fits around the existing Melzi standoffs, and can be held...

Complete case for board maker's general L or board maker's general 1.4. Top part of the cover features a magnetic mount. Magnets used are 4x2mm in size. ... Magnets can be found at the following link:...

Users can install a compact 0.8-inch fan that measures 2 by 4 centimeters. ...This component is also compatible with the MKS SGEN-L motherboard.

... adds a fan output on the output of the E1 card. The output is PWM (v1.1.9) -Filament_Sensor_and_BL_Touch: It is a version with a BL-Touch and a filament sensor (1.1.9) -Marlin-bugfix-2.0.x_Version_Finale: MKS Gen L, BL Touch, LCD2004 screen (v2.0.0)

... is PWM (v1.1.9). -Filament_Sensor_and_BL_Touch: A version with a BL-Touch and a filament sensor (1.1.9) has been created. -Marlin-bugfix-2.0.x_Version_Finale: I have made MKS Gen L, BL Touch, LCD2004 screen firmware available for use (v2.0.0).

As no satisfactory rendition of this print circuit existed on GrabCAD, I chose to create my own design. ...Suiting my requirements, this model proves sufficient, and further enhancements are not planned.

This case is totally exposed, requiring you to add your own top to seal it - whether using a fan or not. The motherboard is securely fastened inside the case, and the case itself can be screwed into any available support. There's ample space to route...

Case for MKS SGEN L v2 motherboard case with cooling fan.

I have a MKS SGEN_L board and I wanted the MKS TMC2209 v1.0 drivers to produce an endstop signal for sensorless homing. This issue only applies to the MKS TMC2209 v1.0 drivers; they corrected it in version 2.0. In addition to setting the diagnostic...

... I really loved the idea of making microUSB compatible and fully integrated into the stock aluminum case. ... So after a few hours, here is my custom version. Where to purchase: - SKR v1.3: http://bit.ly/2TKJQvY - MKS Gen L v1.0: http://bit.ly/2TGKWZI

... USB cable without making any holes, and the microSD is fully accessible at all times. Where to buy: - Connect your printer seamlessly with SKR v1.3: http://bit.ly/2TKJQvY - Upgrade your printing experience with MKS Gen L v1.0: http://bit.ly/2TGKWZI

Still a Work in Progress Ask Your Question or Leave a Comment It's a Creality Ender-2 box case designed specifically for the MKS Gen-L V1.0 board and the MKS TFT28 touchscreen. A 40x40x20 Noctua fan or similar can be mounted on the front right...

The missing end is finally fixed at the bottom of the box. I've remade and repaired the top part in boot mode. Here's what I've done: Solid: No fanholes on top! You can design it however you want. Variation 1: One 80mm fanhole with a honeycomb...

Human: Hardware + Four Original x4 M3x6 screws, plus a couple more of the same, are required for installation. Installation + Due to imprecise routing around the edges, fit may vary with these boards. My own was somewhat tight. + Begin by partially...

Remixing the case cover involves drilling additional holes to accommodate an 80mm fan, which happens to be the exact size of the fans I currently have in stock. To get started, carefully position the modified case cover so that the area where you...

Remixed from: https://www.thingiverse.com/thing:3676494 I had to modify it a little because of the linear rail. I have also added a bottom fan since a use a feet that lifts the printer. The box was designed for M3 inserts. ... Fan dust...

I modified it a little because of the linear rail's constraints. I added a bottom fan since I use a foot that elevates the printer. The box was designed specifically for M3 inserts. ... Fan dust filter:...

This box was originally designed for our DADSON PRUSA i3 3D printer project that my son and I are building together. Go check out my Instagram page for details: https://www.instagram.com/bywebberen/ It has space for dual 40mm fans and the reset...

I'm upgrading my JG Aurora's stepper drivers to TMCs, which demand active cooling. A 60mm Fan was purchased only to discover later that there was barely enough clearance for it - a mere 5.0-5.5cm. To address this issue, I designed an additional...

Mount adapter for 32-bit MKS Sgen_L V2.0 board in Sunlu S8. Sdcard slot is completely aligned with hole in cover. USB connector slightly displaced in left side, hole in cover can be extended. ...Right bottom mounting hole in MKS PCB must be extended for...

A remix of my MKS Gen V1.4 / RPi case with additional mounts for the SKR V1.3 & Pro boards. The new SKR PRO version is untested as I do not own one, and all measurements were taken from a reduced mesh of the PRO board model available on BigTree's...

Firmware is preconfigured for MKS Gen V1.4, DRV8825* and 2004 LCD** (Cl-260 standard display) but should also work with MKS Gen V1.3 as pin-layout is identical. MKS Gen V1.4 and 5xDRV8825 can be bought cheap as a SET on Aliexpress. DRV8825 drivers...

The firmware is preconfigured for MKS Gen V1.4, DRV8825*, and 2004 LCD** (Cl-260 standard display) but should also work with MKS Gen V1.3 since the pin layout is identical. You can buy an MKS Gen V1.4 and five DRV8825 drivers as a set on Aliexpress....