mlok to pic rail adapter 3d models

A simple conversion device allowing a 45-millimeter fan to be safely connected to standard equipment featuring 30-millimeter fan outlets.

This is a remix with the center hole scaled up to 53mm. ...No other changes were made to the original model

Allows you to insert a common 120mm computer fan within a 4" flexible hose. ...Helpful to exhaust printing fumes for FDM or resin printers.

I don't like to use hand or leg pumps to pump up inflatable mattresses when my friends or relatives comes over.

garden hose to 40mm drain pipe. ... garden hose connection to rinse a 40 mm drain pipe. ... fits almost all quick connect garden hoses.

this can be used to mount to your monitor in this orientaion but I am sure there are much more things you can do

Allows you to convert PVC piping you can find at any home store to supports for the most common plastic shelving.

The design is available on OnShape (most notably to edit tolerances)

... ...To determine the correct length, aim for screws measuring 11-12 mm in length. The purpose of the eccentric hole on top is to provide a means to insert a screwdriver or other tool to safely remove the LR6 battery from its housing when needed.

This is an interface converter from a standard Zodiac fitting to a universal garden hose inlet.

If you need to mount a 50mm fan instead of a 40mm one.

Individuals Require a Flexible Connection Tool Ranging from 16x1 to 24x1.5 Millimeters in Diameter.

Created specifically for the Geetech A10 to operate the Ender 3 hotends effectively.

Adjust the 52-millimeter gauge to fit snugly within a standard 60-millimeter pod.

... design. ...I wanted to print it without any supports or bridging for a cleaner end result, as well as be able to tweak the sides independently for a perfect fit. The tradeoff is that the two halves have to be glued together. ...CA glue works very well.

Mounting bracket for Reflex accessories, allowing you to attach a microphone, flash, or other component separately.

Can be used for http://www.thingiverse.com/thing:191347 to use more standard slide sizes

Used to attach a bike chainring on a GROB 0710-2-20 Shaft

Extend an 30mm NVMe to 80mm. ...Work with a 0.7mm thick PCB.

I wanted to reuse my Fifine (K670B) microphone stand with ESR Wireless Charger (HaloLock).

... design. ...I wanted to print it without any supports or bridging for a cleaner end result, as well as be able to tweak the sides independently for a perfect fit. The tradeoff is that the two halves have to be glued together. ...CA glue works very well.

... major bicycle component manufacturer, be prepared for a challenge when loosening the retaining ring that holds the disk in place. ...To make this process easier, simply add a ratchet equipped with a 32mm socket to your toolbox and you'll be good to go!

Attach a Hydrapak Seeker bladder directly to a Sawyer Squeeze filter.

... to the 12-volt device using a soldering iron. ...Then, place a 200-watt DC-to-DC converter between them. I purchased this one from Amazon: https://www.amazon.com/dp/B07RGWJHPZ. Before connecting it to any 12-volt device, set it to output 11 volts.

I was in dire need of a solution to this problem.

This remix allows you to decentralize the 5015 fan, useful in some situations.

... pusher into a Vulcan enables a seamless conversion from a belt-fed to a magazine-fed blaster. ...To ensure optimal performance, you'll need to fine-tune the thickness of the square component featuring four holes to perfectly align the pusher.

Needed to fit a 40mm fan into a 30mm space. ...This extrudes out 22mm.

Modifying a 40mm PC Fan to Fit a 35mm Housing Space

Remixed this to be a bit longer from https://www.thingiverse.com/thing:219625