mlok to pic rail 3d models
3287155 3d models found related to mlok to pic rail.
grabcad
made this for a friend when fixing his paintball gun, so he could put attachments on it.
prusaprinters
Uses standard MLOK hardware and occupies one slot. Flares to the side of the mounting surface are 45 degree. Print with PLA+ and 6 perimeters. Set with the MLOK interface facing up. Support will be needed on the inside flat. ...Organic recommended, for...
thingiverse
Caliber labels for MLOK systems. ...Requires 4mm or 5mm MLOK hardware.
thingiverse
Using the lower half of the sight created by alliedsport, I replaced the sight with picatinny to add other pic attachments to my Reflex 6. The lower half fits perfectly and snaps into place over the Reflex 6 top rail. I used .3 layer height standing...
thingiverse
Most Picatinny rail attachments use a bolt passing between the grooves of the rail to help mechanically secure attachments to the rail(in addition to clamping forces). ...Print two of these and place them on the rail with a gap between them so the bolt...
thingiverse
They are designed to be vertically oriented, but seem to be perfectly usable at an angle as well, I got the idea from reddit, https://www.reddit.com/r/ar15/comments/klxoxs/vertical_mlok_ar_wall_mount_idea_for_3d_printer/ It handles a G3 with a bipod,...
thingiverse
I wanted a slim handguard that had usable MLOK slots and could not find one that did not require converting the rifle to a free float system so I created it. I printed using PLA, Nozzle temp 210, bed temp 65, Supports, and 25% infill. I would...
thingiverse
This is a Weaver 3/8" rail to picatinny rail adapter I designed to go on top of my Marlin Model 60. ...Tight fit to the weaver rail, also has hole to allow the use of a M3 bolt to act as a set screw.
thingiverse
A low profile top rail for the Novritch SSP1. ... A M3-35mm Phillips or Allankey bold and a M3 Nut is used to fix the botom rail in place. ... (It schuld hold on ti's own)
cults3d
Mlok style vertical foregrip grip with stippling for any keymod/mlok rail
prusaprinters
They are designed to be vertically oriented, but seem to be perfectly usable at an angle as well, I got the idea from reddit, https://www.reddit.com/r/ar15/comments/klxoxs/vertical_mlok_ar_wall_mount_idea_for_3d_printer/ It handles a G3 with a bipod,...
thingiverse
Modified the original part to fit Scheppach/Grizzly rail. Also strengthened the rear attachment point to the saw. ...Finally, added some holes because it looks cool.
grabcad
Designed to hold two rails of Picatinny of Wiever rail together if necessary.Consists of two parts. ...Printed from polyamide on a SLS 3D printer.An M4 threaded screw with a hex head and a knurled nut are also required for M4.
thingiverse
[01/05/2022] UPDATE: All files migrated to Printables: https://www.printables.com/model/186740 Glock rail to Picatinny adapter, for when you want to fit a pic rail only item or mount. Gives you 5 slots. Made it as low-profile as possible while still...
prusaprinters
Glock rail to Picatinny adapter, for when you want to fit a pic rail only item or mount. Gives you 5 slots. Made it as low-profile as possible while still maintaining the correct picatinny dimensions. Fitted for Gen 4, haven't tried on other...
thingiverse
Simple short ish vert grip for mlok slots. Uses two 1 inch bolts with mlok keys. ...Printed with the mounting surface on the bottom with support structure.
thingiverse
... designed around Tattu 11.1V 3S 850mAh 75C LiPo. ...Compartment dimensions are 60x30x25mm. Will need mlok hardware to mount to handguard. ...Cap is designed to be friction fit; if too loose add a layer of electrical tape along the edge of the cap.
cults3d
... only - Gas pedal/thumb rest not included. Mount with 2 M5x10 and M5 Tnuts or Mlok studs Original design created by another. This is a modified version of the original to be sturdier around the base as I found the original to be weak when mounted.
thingiverse
... black flash hider was nowhere to be seen, so I took matters into my own hands and crafted a custom cover that fits like a glove. It turns out this easy-to-install accessory is compatible with other models featuring the same KWA Mlok style design.
thingiverse
In the event that you receive a new barrel assembly with the Pic Rail (Finger Burner 9000) removed or have it removed from your existing assembly, there will be a gap between the Handguard and the Chassis.This is a series of 3 different spacer...
thingiverse
Handguard für die SAR12C mit MLOK kompatibel Befestigung über die originalen Aufnahmepunkte mit Schrauben und Muttern
thingiverse
1913 Picatinny rail to milspec buffer tube adapter. Use M4x35 screws for extra security when attaching to the back of a lower. ... Print with threads facing upwards for best results ( I'm a complete 3d design noob, Use this at your own risk.)
prusaprinters
This adapter allows you to attach NATO Accessory Rail camera accessories to a standard 15 mm camera rail consisting of two rods with the diameter of 15 mm, spaced 60 mm apart.The photos show two of these adapters, one printed in PLA (gray), one in...