mmu2s upgrade 3d models
32263 3d models found related to mmu2s upgrade.prusaprinters
Original Prusa MMU2 to MMU2S upgrade printable partsNote, these are not the parts for the MMU2/S unit itselfnor the parts for the i3 to MMU2S upgrade.
thingiverse
Just upgraded to MMU2S and I did not liked the fact that the wire needed to be pinched in the hinge so I edited the original prusa design.
thingiverse
My quick bolt upgrade for the Prusa MMU2s is easy to print, just use PLA with 0.2mm layer height and print them slow and one by one to strengthen the thin walls at the top. Don't use PETG, I tried PETG and it broke off after some time. No problems...
prusaprinters
I used the tight fitting of the M3 handle by Remi-Rafael (https://www.thingiverse.com/thing:5532943) and designed a matching handle for the mmu2s around it.My quick bolt upgrade for the Prusa MMU2s is easy to print, just use PLA with 0.2mm layer...
prusaprinters
A colleague need this windows to mount his MMU2S on his prusabox, I made these models using my acrylic windows as a sample. Made left version with and without window for MMU2S data/power cables, the version with window cant be removed without...
prusaprinters
<p>Never loosen the threaded insert again.</p><p> </p><p>Parts:</p><p>1x ruthex® threaded insert M5</p><p>1x 21mm PTFE-Tube(2x4)</p><p>Countersink both ends of the PTFE-Tube.</p>
prusaprinters
<p>3/5/5/25% PETG or ABS </p><p>PTFE connector - <a href="https://amzn.to/3HyMm0u">https://amzn.to/3HyMm0u</a></p><p>Print upright, narrow side down with 0.2mm. </p><p>Tested in ABS CR3D MagicBlack on Voron V0.1. </p><p>Is intended for...
myminifactory
It contains: 2cm higher corner pieces A 2cm higher magnetic door holder New holders for the MMU2 A bushing to guide the PTFE tubes out of the enclosure A filament guide to feed the MMU from top of the enclosure A 90° turned spool holder useful...
myminifactory
It contains: 2cm higher corner pieces A 2cm higher magnetic door holder New holders for the MMU2 A bushing to guide the PTFE tubes out of the enclosure A filament guide to feed the MMU from top of the enclosure A 90° turned spool holder useful...
prusaprinters
One may say that I was fed-up getting on my knees looking through the workshop floor for dammed bearings.... So, here is my take on the Prusa MMU2 Spool Bolder Bearing Clamp I added a Filament Guide that works on my IKEA Lack table. Keeping the...
prusaprinters
<p>I liked the ones from Thierry but wanted to save some space so two could with next each other on mu Ikea Lack wall shelf. So I cut them in half and added some to hold the bearing in place. ...Got rid of the yellow thingies with the printer.</p>...
prusaprinters
You can use the file list and folder structure here to prepare parts in the same order as you will need them according to the guide.adapter-printer-mmu2s part differs for MK3S+ and the older MK3S/MK2.5S.The oldest of the family, MK3, has to be...
thingiverse
So, here is my take on the Prusa MMU2 spool holder I added a Filament Guide that works on my IKEA Lack table Keeping the original Prusa Spool Holder Parts: Simple Bearing Clamp, works as is. ... Filament Guide - PTFE tube can be added if required Also...
myminifactory
This is an upgrade to the original Prusa MMU2 upgrade for the pimp your prusa contest. It provides an access hatch and dust bin for the puley body. Currently the pulley body traps dust, gear grounds and cutting fragments from the filament changing.
prusaprinters
This is a Magnet improvement to the MMU2S (R2) Selector PINDA part.The only modification, I made, was to place a 6x1 mm round super magnet under the steel ball and filament path.This magnet will keep the steel ball down when the filament is redrawn.
prusaprinters
With this upgrade you can keep your filaments dry and organized in a very small footprint.You do not need anymore the filament buffer.These designs should be compatible with all 200 mm Spools which has a round (Das Filament type) or flat edge...
thingiverse
This is a Bear Upgrade friendly version of the same horizontal brackets I designed for the Multimaterial Upgrade 2. I designed these in Tinkercad so no source files are available. I haven't had a chance to print these out as I haven't completed my...
prusaprinters
This is a Bear Upgrade friendly version of the same horizontal brackets I designed for the Multimaterial Upgrade 2. I designed these in Tinkercad so no source files are available. I haven't had a chance to print these out as I haven't completed my...
thingiverse
... coil holder. Both systems are the same and offer a very good and stable hold. Material: PETG Perimeter: 3 Infill: 20% Gyroid Have fun printing :) Credits: Goes to Mr. Bear (Prusa Bear Upgrade) https://www.thingiverse.com/thing:2808408
thingiverse
MMU2 frame mount for my Bear Upgrade printer or for Openbuilds V-Slot based printer. ... BOM : - 2x M5x10 screws - 2x T-Nuts Check out the Bear Upgrade project here : https://www.thingiverse.com/thing:2808408 If you are using the Bear Extruder you can...
thingiverse
As original arm didn't work reliable and caused friction, this seems to be the better solution and only requires a few 7cm long bowden tubes
prusaprinters
E2 - stock magnet 2×6×10" mm" by darBis https://www.thingiverse.com/thing:4104419 It is probably the single most important upgrade for the MMU2S from my point of view. "Prusa MMU2S Rear PTFE Holder" by iwagner...
cults3d
Other UPGRADES for the MMU2S I use and recommend: "Prusa MMU2 Selector with magnet and opened FINDA canal ver. E2 - stock magnet 2×6×10" mm" by darBis https://www.thingiverse.com/thing:4104419 It is probably the single most important upgrade for the...
thingiverse
Other UPGRADES for the MMU2S I use and recommend: "Prusa MMU2 Selector with magnet and opened FINDA canal ver. E2 - stock magnet 2×6×10" mm" by darBis https://www.thingiverse.com/thing:4104419 It is probably the single most important upgrade for the...
thingiverse
remixed the original for 30 degrees, as the 45 degrees caused the tension screws to fall if you opened the cover
cults3d
This model or parts of it CANNOT be sold, shared or distributed in digital, physical, original or modified form This is designed for Multi-Material upgrades such as MMU2S by Prusa and Pallete2S by Mosaic. I do not own any of these upgrades and this...
thingiverse
All props to pekcitron for this design; I just took the f3d files he provided and added a hook so that the MMU can clip onto the frame without screw hardware (like the original mount does on the stock frame). I left the screw holes so you can still...
prusaprinters
Hi i painted this for your MMu2s upgrade. ...I hope that it will work.</p><p>Only you can download it because it is in the G-CODE</p><p>It is not my model but i painted it for you and downloaded on the PRINTAEBLES.</p><p>Please download it and like it...
thingiverse
Filament guide to be used on the spool holders provided with the Prusa MMU2S upgrade kit. Helps to improve feeding of filament into the buffer and reduce the potential of the spool unravelling and causing feed failures. ...
thingiverse
The original, shipped with MMU2S upgrade didn't really work for me. It is designed to be put in back of printer, where it doubles the size of the printer itself. Also I found it very hard to manage filaments in the buffer, and additionally, it won't...