mmu2s 3d models

As you can see from the photos, I'm not relying on the standard Prusa MMU2 spool holders or the accompanying brackets to keep filament in check during ejection from the MMU. Instead, I've opted for a split PTFE tube setup. Initially, the tubes were...

This is a remix of JacquelineVB's remix of a Gible.I've split it into 5 models so that it can be 3d printed in multicolour on a Prusa MMU2 or a palette pro.Eyes are done as a single colour as the scale I'm printing it for our Pokemon Go Communities...

It is then inserted into the main body and held in place by press fitting the 8mm aluminum rods that came with the MMU2S into and through the roller. NOTE: it is a very tight fit for the rods and they will need to be cut to length. I found it...

I probably had to take the MMU2 apart 10 times during the print. I used Prusament PETG filament and the default filament profile. It was very frustrating... but it was better than the ABS/ASA fumes. I also kept getting blob nozzle jams when I tried...

... but you may need to print 99% or 101% scale depending on your PLA brand/printer setup. Better to start to big (lose) than Print to small and struggle to remove.The provided gcode has MMU2s Filament 1 as the main body and Filament 2 is the letters.

This is a multi-color version of a headphone stand shaped like a treble clef by muddymakerNO SUPPORTS required, files are in the correct orientation for printing in multi-color mode on a Prusa MMU2. ...For single-color printers, the clef body can be...

If you're using the MMU2, you'll need to swap Pink out for Black once it's done with Pink.You'll need twelve 6x2mm round neodymium magnets per llama (6 per half) to install into this fidget. Cheap off Amazon. ...The gcode is for two Llama Fidgets, so a...

Every time I flip open the MMU to work/clean, the bolt falls out, the spring rolls away, and I spend half an hour on the floor with a flashlight. No more. Add these to your bolts, probably tighten the bolts a half turn less, profit. For other Prusa...

... ... Shown here, https://www.printables.com/model/77054-mmu2s-buffer-inspired-by-rmu-bufferIt is designed to mount the buffer without modifying the buffer bottom.  It fits the outside, right, left and possibly back side of the Original Prusa Enclosure.

I had varying degrees of secureness and the paper made them very snug. Works great as a combo with my lack ptfe tube guide: https://www.thingiverse.com/thing:3129101 Using them after days of MMU2 printing has resulted in zero tangles or the guide...

This three-reel version utilizes the tubes and bearings that come with the Prusa MMU2 kit and has space for two 100mm wide reels (same as MMU2 rollers) and one 86mm reel (wide enough for Prusament 70mm reels). There are two options for the dry...

If you have a Prusa I3 MK3s with the MMU2s, and you upgrade the extruder to use the Bondtech BMG, then this part is for you. Sorry there are so many qualifications. With the normal Bondtech BMG upgrade there is a filament sensor that involves a...

Multi-color Print This is a 3D print designed to be printed on a Prusa Mk3S with MMU2S multi-filament attachment. It can be printed as a one color button or a two color button. If you have a MMU2 change colors after 3mm. If you have a one color...

NOTE: UPDATED Version WITHOUT Brake for new MMU2s can be found here (Complete redesign)-> https://www.thingiverse.com/thing:3571725 A multi-spool holder that works with Wall Control pegboards. I wanted a spool holder that got the spools off of my...

My daughter then suggested using my new MMU2, so I revised the design to make it multi-colored. This required about 30 meters of filament, which I used on both my Palette 2 and MMU2 printers. The prints turned out beautifully, thanks to the generic...

A NEW Version WITHOUT Brake is now available, especially designed for new MMU2s! Find it here (Complete redesign) -> https://www.thingiverse.com/thing:3571725 I created a multi-spool holder that works seamlessly with Wall Control pegboards, keeping...

 Have a look at the attached image for reference of which color is where: Purple MMU2 position #1, Blue MMU2 position #2, Orange MMU2 position #3  IMPORTANT NOTES: The Multi-Color STLs are only for multi-color printers.  They can not be printed...

Pin is locked, centered, and secure. And... I test, optomize and tune small batches of 4 color buttons then run sets of 25 or so on Prusa Mk3s MMU2s to minimize purge blocks waste. Model files were created using Illustrator and Rhino3D, converted to...

 Have a look at the attached image for reference of which color is where: Purple MMU2 position #1, Blue MMU2 position #2, Orange MMU2 position #3  IMPORTANT NOTES: The Multi-Color STLs are only for multi-color printers.  They can...

Why another Filament Buffering Solution? I wanted a solution that met the following requirements: Does a decent job of handling retracting filament (duh) Fully 3d printable while ideally using a minimal amount of filament Retains maximum visibility...

It requires to retract all five filaments from the buffer, and then again feed five filaments through the buffer to the MMU2S.Therefore, I decided to have two buffers on my Mk3S, one for each material kind. Then it becomes matter of swapping the 5...

Then, if you do not have an MMU2S, after they position themselves on the virtual build plate, change the printer settings to whatever printer you are using. The ruler and pin can be printed together so that only 2 color changes are needed at layers...

The MMU2S does not include a printable plate for the filament buffer. I have several brittle filaments that were almost impossible to load without breaking. The only technique that worked was fingering them all the way between the buffer and MMU. I...

Opening is big enough to fit a hand through, so it's also good for simple backside maintenance work and dis-/connecting the PTFE tubes when combined with https://www.prusaprinters.org/prints/22339-prusa-mmu2s-rear-ptfe-holder . Print instructionsI...

You can also install a filament tube from the extruder/MMU2 to the frame in two ways: above (using a tube holder) or below the spool. The slope of the track can be adjusted by placing objects under the frame and/or by screwing two M3 bolts into...

If your PTFE tube breaks off in the connector, no problem, just unthread it and put in a new one, it's now just that easy since I know you probably got them in a pack of 10 ;)The original Prusa .STL file for the extruder filament sensor upgrade for...

Immediately when I saw this maker coin for the Prusa Community's December print contest I knew I wanted to print this with my MMU2.0. <a href="https://www.prusaprinters.org/prints/1071-print-in-place-geared-maker-coin">Boba Maker</a> was kind enough...

Please make sure to have your MMU2 running fine before installing the buffer.\r\nIf your MMU2 works, you will like the buffer though.\r\n\r\n#Changelog\r\n\r\n2019-07-09: changed *Buffer3_part2-buffer_part_2-18.stl* more clearance for the filament...

01/30/19 - I've added a new design with the Prusa Research logo as suggested by Boba Maker Print instructionsIf using the provided 3MF files note that I've set some settings for my MMU2 outside of the defaults. Please look at these prior to printing...

- PINDA Adjustment &amp; Positioning Tool(Achieve the perfect SUPERPINDA position)MMU2S Single Filament Guide Festo M5 Coupler(Retain your original MK3S spool mounting while still using MMU2S in single color...