mobius 2 camera 3d models

Camera Shroud for Mobius 2 cam. ...Just requires an 8mm hole in the airframe and uses the mount supplied with the camera.

This part allows fixing a Mobius or a Runcam2 HD camera to the belly of Eachine Razor, which is a great plane, but hard to fix an HD camera on... Warning: this will hurt your camera if you land on hard surfaces. Land on soft materials or tall grass...

... yellow to find it easier in grass. Strap + mount + camera = 57grams Angle difference is 60 degrees. I hope this helps somebody else with a mobius mini 2 camera. ... If you like my designs and you wish to tip me I greatly appreciate it!

Version 2 of my Mobius camera anti-vibration mount. Find version 1 here:http://www.thingiverse.com/thing:538604 The main improvements with respect to the previous version are that the design is more precise, thanks to my design skills getting better,...

A great print to zip tie to your next project! Printed in flexible TPU to minimize vibrations! If interested in a 60 degree mount, drop me a line and I'll upload it. ... Make sure to check out other free stuff on my website www.typhonfpv.com

Hat Clip for Mobius 2 Action Camera Print using just perimeters. ...PETg preferable but PLA will work too

This is a lens cap and lens protector for the Mobius 2 camera. The protector needs a piece of clear plastic cut to fit inside. I used lexan that was 0.02" (0.51mm) thick. You may use whatever thickness you'd like but I'd recommend less than 0.06"....

A simple quick release GoPro compatible adapter/mount for the Mobius 2 camera. Just slide the camera in to the enclosure. To remove, just push down on the tab and push the camera out. It has a cut out on the side so you can access the buttons. I...

A simple quick release GoPro compatible adapter/mount for the Mobius 2 camera. Just slide the camera in to the enclosure. To remove, just push down on the tab and push the camera out. It has a cut out on the side so you can access the buttons. I...

... GoPro style action cam. ... Lens ribbon cable (link provided below) in order to twist the lens into its new position.http://www.ebay.com/itm/Mobius-Actioncam-1080P-2-5-CM-26-Pin-Lens-Extension-Cable-/291415457724?hash=item43d9b6ffbc:g:l4oAAOSw7aBVEkLx

... for Mobius Camera onboard RC planes. ...Print 2 supports and one base, CA glue together with 5mm layers of foam under the camera for vibration damping. Or glue base on top of leg cross bar. ...Yellow version is PETG, white one is PLA, both work fine.

Mobius camera easily slides in and out of this mount, with excellent retention. ... Printed in ABS with 20% infill.

This is the case and the cap of Mobius action camera. ...The external is very similar , the internal is similar.

http://www.ebay.com/itm/Mobius-Actioncam-1080P-2-5-CM-26-Pin-Lens-Extension-Cable-/291415457724?hash=item43d9b6ffbc:g:l4oAAOSw7aBVEkLxPost-PrintingI printed this in PLA and other filament should work just as well. Some filing around the usb port...

New features include: Lens swap to the front of the camera Flatted out the camera bottom to provide more stability when mounted Zip-tie loop to easily secure the camera and eliminate risk of camera being ejected from aircraft To make the mod work you...

Use this model of the Mobius camera to plan out your project or test the size of your gimbal. ...Created by Henrik Sandaker Palm.

Mobius Mini camera slides in and out of this mount easily, yet has good retention. ... Printed in ABS with at least 50% infill.

light mount for Mobius Mini Cams. ...You can fix the mobius with a cable tie or velcro strap. The holder itsel can very easily fixed with 2 strips of tape on a flying wing or fuselage for example.

The notches are for zip ties to wrap around your rear view mirror bracket and the cable for camera. It takes a one M3 x 20mm screw and nut and washer. ...Print Settings Printer: Prusa i3 Mk2 ...

This is a case for the Mobius Camera. It has protected my camera through many RC aircraft and copter crashes. ...The long lens edition should be used with the C type lens.

Inspired by JakeKing's build http://www.thingiverse.com/thing:71492 Here's my version of a Mobius Camera Gimbal. Also added is an optional shock-mount ("anti-jello"). ...This will be used on an upcoming FPV Fixed-Wing project (excuse the Mobius mock-up,...

Simple Mobius camera mount for drone. Meant to be printed in a flexible material (i used TPU and the result meets the requirements :-) Inspired by [this design](https://www.thingiverse.com/thing:1978412) and redesigned for the new version of the...

... three parts the slide into each other. There is the mobius case itself which holds the camera, a block which can easily be printer in different angles, and the clip which which holds it at the printer. ... This makes it a very flexible solution.

I wanted to use my Mobius action camera to take time-lapse video of prints on my Monoprice Select Mini V2, but I couldn't find a GoPro-style pivot bracket for it. I used eMachineShop to create this bracket. It fits perfectly in the Mobius' base...

Simple servo driven 2 axis gimbal designed for the mobius action camera Instructions After you 3d print the 3 pieces you will see that there are multiple small holes. This holes will need to be drilled out in order for the servo shaft to be inserted....

Simple Mobius camera mounts in 10°, 15°, 20°, 25°, and 30° flavours. ... Camera is a snug push fit into mount but for a bit of added security the mount allows a rubber band to be used to squeeze the top together.

This is a Mobius Camera hat holder. It uses rubber bands as fasteners. I think its better preseving the camera. ...The clip was taken from the thing http://www.thingiverse.com/thing:397806 which is a nice holder too and does not require to have rubber...

This is a mount for the Mobius camera that will clip to the brim of a hat. Instructions Print the camera clip with support. Glue the smooth side of the Hat Clip Base to the bottom of the camera clip. Then glue the short end of the hat clip to the...

Very light support for the Mobius camera. You need a 5mm carbon rod of tube (could be aluminum too) The carbon rod is press fitted into the support hole, if not tight enough just glue it. ... The support itself is taped on the body of the plane.

Use your Mobius camera as a windscreen mounted dashcam. The mount is tilted by 25 degrees to keep the camera horizontal in my 2003 Saab 9-3, but I guess this is a common value and will work just as well in other cars. ... The five small holes can take...