mobius action camera software 3d models

This is my best diver camera yet! I made two big slots on the sole for easier handle mounting. To match the rod endpoint diameters with Dinkum FlexiJoint pieces (30 mm), I shortened the overall length to 238 mm, now it fits a 200x200 mm build plate...

Since they resemble GoPro mounts, I assume they will also be compatible with those cameras (although this has not been tested). To assemble the mount, you'll only need a few extra screws. I had 6mm screws available, so I drilled corresponding holes...

A flashlight and camera mount made for Convoy S2/S3 flashlights and a Drift camera mount. It features a generic GoPro mount on the base so it's compatible with nearly all off the shelf camera mounts including the one that came with my Bell Super. ...

... ...A massive camera strapped to a 3-inch quadcopter - no problem at all! My newly designed face plate is a huge improvement over its predecessor. ...Printed in PETg using my trusty Printrbot Simple Metal, the results are nothing short of fantastic.

Customized Version of Thingiverse Object: http://www.thingiverse.com/thing:1324211 Built Using Customizer Tool: http://www.thingiverse.com/apps/customizer/run?thing_id=1324211 Instructions for Use: Utilizing the Following Settings: * Face Resolution:...

The distance between these holes is precisely 34 mm both vertically and horizontally, allowing for seamless camera placement. The joint part itself measures a total width of 14 mm, excluding the nut, while the middle fin and spaces between them...

To assemble this handle, you will need the following components: ## In the base Two 1/4-20 UNC threaded inserts (I recommend using these - the holes are 8mm in diameter, making most threaded inserts suitable; just heat them with a soldering iron and...

... as well) . The "thumb screw" is designed to fit around a standard 0.5 in. long 1/4" x 20 hex bolt and secures the grip to the bottom of the camera. I printed with 100% infill for rigidity and to limit the amount of water that can penetrate the grip.

A versatile frame designed specifically to work seamlessly with GoPro mounts, allowing users to capture high-quality footage without compromising access to essential camera functions. This frame cleverly allows for effortless battery replacement,...

I used the Sj4000 Wifi Two-Sided Frame model by MileHighDesign camera holder from Thingiverse: http://www.thingiverse.com/thing:633830 Print Settings: Printer Brand: Deltaprintr Printer: Deltaprintr Kit Rafts: No Supports: No Resolution: 200 microns...

It was: - Cheap camera AKASO V50 but better than phone. With a very small and very hot battery for half an hour. - Cheap good stabilizer. It is not good to use it with a phone because of a very poor android application. - The best simple battery...

Thingiverse.com/apps/customizer/run?thing_id=1324211 Instructions Using the following settings: Number of slices (N) is set to 4 Smoothness level is at its lowest setting, 0 Tolerance limit (tol) has been adjusted to 1 unit Maximum camera dimension...

... and it has room to press fit a nut for the GoPro screw. For the camera holder, I used the Sj4000 WiFi 2-sided frame model by Milehighdesign. ... I printed this part with my Deltaprintr printer using a resolution of two hundred microns or lower.

The firefly snaps into place with ease, and I still recommend using a battery strap to secure the camera firmly in position. This particular print is crafted from PLA, yet a material like DFU or PETG might offer even greater strength. ...I'm more than...

I used to sell 3D-printed camera gear (GoPro parts among that) but found that I dont have time for it anymore. I decided to share my models instead. Print with ABS, PETG, ASA, Nylon or any other strong material. Slot for M5 nut that can be clamped...

The "thumb screw" component is intended to fit snugly around a standard 0.5 inch long 1/4 x 20 hex bolt and serves to secure the grip firmly to the bottom of the camera. For added rigidity and to minimize water infiltration, I opted for 100% infill...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing\_id=1324211 Print instructionsCategory: Camera Summary Customized version of http://www.thingiverse.com/thing:1324211 Created with Customizer!

Hello all, Here is a case for an Iphone 13, in order to attach any universal camera support. I designed this so I could attach the phone to a rubber Mouth Support, and record some driving POV's (altough the setup it's kind of heavy, considering...

Hello all, Here is a case for an Iphone 13, in order to attach any universal camera support. I designed this so I could attach the phone to a rubber Mouth Support, and record some driving POV's (altough the setup it's kind of heavy, considering...

I made this mount specifically for my new Firefly 6s camera, and it has a good balance to it. Some drilling is required, but nothing too demanding. The motors used are the high-quality MarsPower 2208 models. Feel free to customize as you see fit -...

I used to sell a variety of 3D-printed camera accessories, including GoPro parts, but I no longer have the time for it. Instead, I've decided to share my designs with others. To ensure a strong and durable print, use ABS, PETG, ASA, or Nylon...

I'm thrilled to share my latest creation - a sturdy Holder / Mount specifically designed for Sony FDR-X1000 cameras and two flood lights! It's built with standard mount sizes in mind, ensuring seamless compatibility. Measuring 160 mm in length, it...

I used to sell 3D-printed camera gear (GoPro parts among that) but found that I dont have time for it anymore. I decided to share my models instead.</p> <p>Print with ABS, PETG, ASA, Nylon or any other strong material. Slot for M5 nut that can be...

... some washers/nuts to fill the extra space. I printed with 80% in-fill and auto-supports, with a raft at 210/60 degrees celcius. Supports came off cleanly and the design fit everything well such as the action cam mount, screws, nuts/bolts etc.

Mounting this to the drone is very easy, first unscrew the four screws at the front, put the Mount on and screw them back, then use one of the included battery straps to hold the Camera in place. This can be 3D printed with no support on PLA in...

I used to run a business selling 3D-printed camera gear, including GoPro accessories, but I no longer have the time for it. That's why I've decided to share my designs instead. These models can be printed with ABS, PETG, ASA, or Nylon - strong...

Renders has been made thanks to Keyshot 7.You have a (Spanish) PDF file to see the explanation of every process.As you can see in images, I made a prototipe, there are a lot of pictures of the process if you are interested in know the way I made...

... Support Structures for the Sliding Bridge. Watch Video Recorded with EMAX 250 Camera Tray & RunCam: https://www.youtube.com/watch?v=PS4dk-AqSLM Video Demonstrating Tray Collapse from 45 to 0 Degrees: https://www.youtube.com/watch?v=kG-SvZ-yPD0

I'm looking to create a design that's safe enough to use with a first-person view system on a quadcopter or mounted on a motorcycle for filming purposes. ... If you need more information, feel free to reach out at ducati.fanatic@gmail.com.

This mount fits any Picatinny rail, featuring a low-profile design and an angled lens at about 10 degrees. It prevents accidental ejecting of the SD Card during bumps from recoil with its extended wall. ...This system works great on paintball guns or...