model scope

While installing a replacement clip for Perceptor's shoulder scope, I broke the pin guides on the scope mounts. Decided to recreate the left and right components for the clip to attach to. The components in question are TAN in the attached picture...

The original plastic that supported the two screws holding this piece in place was only 2mm thick and broke on my wife's scope, so I designed a basic replacement. Made from thicker material, the new plastic is now 3mm thick. I reused the original...

This was designed for the novritsch scope but it is compatible with other 25mm diameter tube scopes. ... 2x 15mm M4 bolts are...

I added a dab of hot glue to the ends of the bolts to keep the scope safe.Cut the filter to fit in the ring, past the lip, with NO GAPS. Wrinkles are fine, and don't affect seeing. Glue in the retaining ring behind it to really seal it in...

You'll want to put the "Super Scope Eyepiece Front" in between the left and right halves of the body before you screw them together, as it has a small tab that captures it and allows it to slide in and out. I recommend gluing the front sight...

Functional and tough riser with a 75mm long rail, you adding 36.5mm offset to your scope line and look through the scope with a mask on a helmet and headphones without any problems. You'll also need two M4 screws at least 35mm long and two M4 nuts.

The two-part design limits the use of aluminum thread, with the "mount_side" part staying attached to the mount while the second part covers or uncovers the polar scope. I highly recommend printing the cover cap at the highest quality settings, as...

I specifically engineered a scope standoff to accompany my stack-on gun safe, yet whenever mine malfunctioned, I found no market replacement available for purchase. Consequently, I opted to design and fabricate one myself using Fusion 360 as my...

The adapter for using the G36 scope handle (Hensoldt HKV A2, Zielfernrohr) on any Picatinny rail. Mirrored Rail_Front_Right_Sided.stl for those guys who want to have the screws heads on the right side. To use this adapter, you should print: 1x...

... front of the Star Adventurer, * Allows you to put in the illuminator, * Allows you to put a unity magnification finder (a.k.a. red-dot finder), to find Polaris easily This really helps with getting Polaris in the field-of-view of the polar scope.

High-precision micro focuser for guide scope with Helical focuser design. ... To bring this project to life, you will need to print the following key components: 1x MF1 module 1x MF2 module 4x precision knobs ### BOM (Bill of Materials) 4x M3 x 25mm...

... larger - I successfully concealed the knot of the rubber string within the hole. This set is for my Zeiss V8 56mm scope, with inner diameters of 63mm and 48mm. ...The Fusion 360 file is included, allowing you to adjust it for other sizes as needed.

http://www.thingiverse.com/apps/customizer/run?thing_id=445259 Step-by-Step Guidelines for Assembly and Configuration Operating Specifications for Optimization: insert_length = 15 mm for Precise Engagement pipe_outside_diameter = 8 mm for Enhanced...

A direct replacement for the original polar scope cover of the Takahashi EM-11 equatorial mount will save approximately 200 grams. Please note that this part does not include a thread, so it is essential to print it in ABS plastic. ...The design should...

This makes sense only when you own a $13 VGA res USB bore scope from eBay or another source, and also download and print the elongated wrapping spool to coil the 1 to 2 meter cable. Now you have a compact solution that can be thrown into a tool box...

I got fed up with the ambiguity surrounding the scope/mount question for EE-3 Carbine prints, so I took matters into my own hands and created my own designs. You might need to do some touch-up sanding, make a few adjustments, and secure everything...

This is an installation guide for a custom scope mount designed specifically for the Daisy RedRyder/1998 airsoft rifle. To get started, begin by removing the top screw from your rifle. Next, carefully drill a precise hole in the designated area of...

This is an innovative adapter designed for use with a 9x50 (Celestron or similar) finder scope to transform it into a guidescope capable of mounting a camera. The GuidescopeAdapter replaces the rear section of the finderscope, allowing you to...

These were not needed but I wanted my own drawing to adjust the scope height to my exact liking. ...So here is the rendering I made from my Buckneer rings.Designed to use with 4x M3x0.5 screws at the top and a 6-32 on the Picatinny Locking plate...

These were not needed but I wanted my own drawing to adjust the scope height to my exact liking. So here is the rendering I made from my Buckneer rings. ... Designed to use with 4x M3x0.5 screws at the top and a 6-32 on the Picatinny Locking plate...

This scope level places the bubble just below you lens. ... You will require these parts: 25mm M4 bolt M4 nut ...

Paragon 3X prism scope dust cover capsParagon3XCap.stl - uses M3x6mm screwsParagon3XCapV2.stl - for use with the rubber bandsParagon3XCapV3.stl - for use as a flip up capsParagon3XCapV3-35mm - for use as a flip up caps with blend grid...

I adapted @falconphysics's Nearly Universal Phone Scope Mount to suit my own needs due to limitations with my telescope. The re-engineering has resulted in a larger but more robust design, allowing for adjustments to the x, y, and z axes to match...

Dew shield designed specifically for the SkyWatcher 9x50 finder scope, which features an outer diameter of 57.4mm. EDIT: New THICK version with 2mm walls has been added because the original design is prone to delamination. Length is 200mm. I...

Since I didn't want to drill into the telescope or use some sort of adhesive, I decided to make a insert that would fit in the slit of my telescope handle that would hold my finder scope. I have a Explore Scientific 8" Astrograph and the finder scope...

There are 3 pieces to this: the plate which is glued into the slot on the TM PSG-1 scope, the fake screw that needs to be printed 4 times and glued into the cavities, and the knob which is popped onto the shaft of the plate. I have designed the...

I recently got a new 34mm scope for Christmas and didn't want to go through the same hassle again. The rings I wanted were over $200 for a pair, so I decided to make my own. They come in different heights ranging from 1 inch to 1.5 inches by .125...

The adapter makes it possible to use the G36 scope handle (Hensoldt HKV A2, Zielfernrohr) on any Picatinny rail. For those who prefer their screws heads on the right side, a mirrored version of the ***Rail_Front_Right_Sided.stl*** file is available....

This zoom throw lever is specifically designed for the Vortex Strike Eagle 1-6x rifle scope. Due to its snug press fit, you may need to adjust your printer's scale settings to achieve optimal results with your chosen filament. For me, it works...

Mount your broken finder scope back onto your telescope. To do this, I used two 1.25" 6-32 machine screws and an 1/8" drill bit to secure the finder to a printed bracket. Next, I attached the bracket to the metal part of my telescope using two 3/8"...