modmic dt770 3d models
77 3d models found related to modmic dt770.thingiverse
UPDATED V1.1 Added generic file that is just the core no extra flange for my cheapo mic, also made the magnet hole larger. I created this because i was too cheap to buy a real mic when i have a decently working cheapo headset. Long story short i...
thingiverse
Hi, This is a remix for a headphone clamp holder, it has increased strenght. ... A small bump so the headphones won't fall off. And special designed for my DT770.
thingiverse
Simple little adapter to fit an MMCX adapter into DT770 Pro's with no modding of the can other than removing the existing cable. ... Insert the adapter into the headphones, then drill the hole out to 5.5mm (measure the diameter of the MMCX adapter you...
cults3d
This is a mod for the Beyerdynamic DT770 headphones that adds Bluetooth without a little brick dangling off your head. That said, it is not for the faint of heart. There will be a lot of soldering, and you'll want to make changes to the CAD and do a...
prusaprinters
Holds a bluetooth receiver. Should also be compatible to BeyerDynamic DT770 DT880 DT990 and possibly others. For more see https://xythobuz.de/2021_09_05_dt770_xlr_mod.html Update 2021-12-15: Made bluetooth holder a bit stronger to avoid it breaking...
thingiverse
... receiver. Should also be compatible to BeyerDynamic DT770 DT880 DT990 and possibly others. For more see https://xythobuz.de/2021_09_05_dt770_xlr_mod.html Update 2021-12-15: Made bluetooth holder a bit stronger to avoid it breaking so easily.
thingiverse
Turn your Beyerdynamic DT770 into bluetooth 5.0 headphones with a simple 3D printed part and a MPOW bh408 holder. Additionally, I recommend that at your own risk, you disassemble the headphones and change the cable to a 3.5mm stereo audio jack. ...
thingiverse
A basic charging station for the MODMIC WIRELESS by Antlion Audio!
thingiverse
This is shaped (almost) exactly like the clips you can purchase from modmic. ...This is used to clip your headphone and microphone cords together.
thingiverse
A simple attachment to replace the sticky pad when mounting a ModMic microphone to the Monoprice Monolith M1060 headphones. ...It clips directly to the stock outer grill.
thingiverse
A plug to cover up the sharp edges on the modmic mount when you don't have the microphone connected. ... You need a 6x2 mm magnet + glue.
thingiverse
These are a set of modmic clips, based on the ones that ship with the modmic, designed to fit on the headphone cords that ship with the Superlux HD 668B. ...Print Settings Printer: Folgertech Prusa i3 2020 ...
thingiverse
Was getting frustrated with the modmic losing adhesion from the k7xx headphones as there was no perfect spot for it. Designed this to allow for a solid surface for the modmic to attach to. ... I printed mine with the pad side down.
thingiverse
... Mounting System by HeyVye. ... https://www.thingiverse.com/thing:2194278 It basically turns the Modmic in a desktop speaker. A 6x2 mm magnet is required and should be glued in. ... Should be printed with supports with the flat side of the hooks down.
thingiverse
1x ModMic Attachment 1x 5x1mm Magnet 1x Double-Sided Tape (1cm diameter circle) The best quality you can set your printer to would be optimal, especially for the 4 little fins that protrude out of the base. ...You may also want to use super glue to...
thingiverse
This is a ModMic Wireless Mount that conforms to the MultiClip standard and is meant to slide into my [modular ear peice design](https://www.thingiverse.com/thing:5894991) or whatever else you may come up with. The magnetic mount that comes with the...
thingiverse
I have a modmic v5 that I wanted to attach to the headset, but the metal mesh wouldn't let the adhesive bond enough to keep the mic attached. The mic and baseplate would constantly fall off even when I cleaned the mesh with alcohol wipes before I...
thingiverse
I created this adapter to connect the Bose QC35 headphones to an Antlion ModMic. The adapter is connected to the original Bose audio cable and is held in place by plugging in the 2.5mm RCA connector. You will need 4x M3 screws to mount the parts...
prusaprinters
The genuine modmic cable clips are far to expensive for this little plastic in my opinion. So i designed them for 3d printing. ...Works quite well for me.</p><p>Single wall print, add brim to hold it to the print bed.</p>
thingiverse
Very basic clip for the modmic Microphone. I only did a few iterations that it feels good enough. I wanted to not glue the magnet in place since that was the first thing failing on the original. The cross is intentionally too thin to print well, it...
thingiverse
After my AKG K99 headphone connectors stopped working, and I bought a pair of earbuds to replace them and wanted a modmic, this bracket allowed me to have the best of both worlds. Print Settings Printer Brand: Printrbot ...
thingiverse
This small holster allows you to hang up your ModMic Wireless anywhere you like. It's intended to be used with another fastener - e.g. velcro, 3M VHB or double sided tape. There is a cutout so you can see the status LEDs whilst it's in the...
thingiverse
Designed for the Antlion ModMic Uni/USB. I made this so that I would not have to use the double sided tape on my nice new headphones. This one was made to be attached to the headband of the Phillips Fidelio X2HR. I'm sure that minor adjustments...
thingiverse
A basic charging station for the MODMIC WIRELESS by Antlion Audio!
thingiverse
A quick revision to the modmic base that gives more surface for better adhesion on more stubborn surfaces
prusaprinters
<p>The small adapter has a fin that screws in behind the cable guide. ...Original screws can be used. The modmic adapter clip seats in the recess.
thingiverse
A holder for the AntLion Audio ModMic dongel to see the status. ... I glued it to the bottom of my monitor with double sided tape.
prusaprinters
It is almost like the original, but with minor tweaks for 3D-printing.I use this for my ModMic Wireless, and it works great. ...Consider getting new doublesided tape as well (3M mounting tape or something like that).</p><p>I've printed this...