mofo brace 3d models
9398 3d models found related to mofo brace.thingiverse
Customized version of https://www.thingiverse.com/thing:1965054 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1965054
thingiverse
Original MOFO motor forward scx10ii kit, skid, 4x4 trans, 6x6 or 8x8 trans and rear frame brace, mounts, etc axial forward motor mount kit, the original MOFO Kit, super low center of gravity, competition style crawling, uses scx10 transmission parts...
thingiverse
MOFO Baja Spurless front motor mount and transmission, servo mount, skid, 4x4 trans, 6x6 or 8x8 trans and rear frame brace. use axial scx10 transmission gear output and roller gear plus shaft and 8x16x5 plus 5x10x4 bearings for the forward mount...
thingiverse
This is a mix of my other MOFO top plate template with an appropriate flip figure.
thingiverse
This is a top plate for the Catalyst Machineworks MOFO racing frame that has a fin on top so one can flip when landing upside down.
myminifactory
This is a FPV camera mount in TPU for the frame MOFO from http://fpvgear.dk/Print two pieces for one camera mount. ... Fits with:Runcam micro camsFoxeer micro camsCaddx micro cams This mount sould be printed in TPU for the best result
thingiverse
This is a FPV camera mount in TPU for the frame MOFO from http://fpvgear.dk/ Print two pieces for one camera mount. ... Fits with: Runcam micro cams Foxeer micro cams Caddx micro cams This mount sould be printed in TPU for the best result
thingiverse
... version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: pen_length = 130 font_spacing = 0.81 word = SEXY MOFO font_scale = 2.1
thingiverse
"hood" and roof for MOFO Rc monster truck chassis for scx24. might have to start a screw or two at a angle to catch hole but works fine. ... v2 version I recessed letters more and extra 2' of angle on front of hood to try and match frame better.
thingiverse
Customized version of http://www.thingiverse.com/thing:305087 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=305087 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:615256 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=615256 Instructions Using the following options:...
thingiverse
New containers lack base to keep drying material away. so making a base was really necessary to make material last longer. keeping the drying material away from water collected from air. this one was made to models sell in Brazil, dont know if...
thingiverse
It is still work in Progress I made the Top plate a little bit bigger because of the screws and replaced the bottom Plate with a Money Clip. I also made an Optional Top Plate based on the Wallet from Jules Winfield in Pulp Fiction, but also...
cults3d
This is an extended receiver tray for the MOFO Ugly AF chassis. It extends an additional 13mm forward over the transmission and adds some additional space at the rear. ... Can also order a print from my store: Shapeways
cults3d
This is a simple battery tray for use with the MOFO RC Ugly AF chassis if you don't want to cut up your stock tray. Also works great for mounting other accessories if you decide to run side saddle batteries. Good clearance all around with countersunk...
thingiverse
The Big boy transmission kit from mofo rc. This is used on a standard scx10 mounting skid plate. uses standard internals in the transmission but requires 2 output gears and more bearings. the standard carrier is for use with the umg6x6 rear axle that...
thingiverse
1/3 of total knee brace for athletes. ...Should be printed using TPU or other rubber/flexible plastic. Meant to be assembled with the main knee brace and bottom knee brace. ...For instructions on assembly look at main knee brace summary.
thingiverse
1/3 of total knee brace for athletes. ...Should be printed using TPU or other rubber/flexible plastic. Meant to be assembled with the main knee brace and bottom knee brace. ...For more instructions on assembly, look at main knee brace summary.
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/ejNif0FKSVv
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/9KsrHfwWBCc