monitor mounted microphone 3d models
361576 3d models found related to monitor mounted microphone.thingiverse
[ENG] An easy way to attach a microphone arm, [like this one](https://www.amazon.com/dp/B08RCYW528/ref=sr_1_28?keywords=microphone+arm&qid=1641992764&sr=8-28 "like this one"), to a monitor mount [like this...
thingiverse
This is a Top mount for the Samsung u28e590d UHD Monitor. ...You can stick your microphone spider on it and hang the microphone on top of your screen.
thingiverse
Using 4 M3*8 screws, this mount fits 20mm(w) x 30mm(h) monitor arms and Microphone Arms with a 12mm Diameter base pole. ...I recommend to use a washer as well to prevent the arm from scraping against the top of the print.
cults3d
Using 4 M3*8 screws, this mount fits 20mm(w) x 30mm(h) monitor arms and Microphone Arms with a 12mm Diameter base pole. ...I recommend to use a washer as well to prevent the arm from scraping against the top of the print.
prusaprinters
Using 4 M3*8 screws, this mount fits 20mm(w) x 30mm(h) monitor arms and Microphone Arms with a 12mm Diameter base pole. ...I recommend to use a washer as well to prevent the arm from scraping against the top of the print.</p> Category: Audio
thingiverse
Monitor or microphone mount for DJI Ronin S. A very simple piece that works very well! ... Ronin S own screws can be used to attach the holder.
thingiverse
After a bit of tinkering over the past several months, I wound up building a box that would mount on the back of the monitor, and grabbed a threaded rod from another project here (I don't remember the specific one or I would link it here). I...
thingiverse
This thing allow you to mount your microphone arm in monitor stand tube (inside diameter 32mm). ...Small convenient and hidden way to mount microphone.
thingiverse
I have a huanuo Triple Mount stand that has a 32.2mm thick bar in back. So I made a cap to go over the bar to hold the mount. I made it with a 33mm diameter 55mm depth to hold the weight and be able to rotate. The Microphone then need a place. so I...
thingiverse
i have included two lengths one for a small monitor and one for a larger (taller) monitor the smaller one is 100mm from the top hole on the vesa mount the larger one is 150mm from the top hole on the vesa mount i am working on a new version that...
prusaprinters
Be sure to use a 1/4 - 20 screw on a power driver to tap the hole. i have included two lengths one for a small monitor and one for a larger (taller) monitor the smaller one is 100mm from the top hole on the vesa mount the larger one is 150mm from the...
thingiverse
A simple Microphone clamp for mounting a microphone spider to an monitor. Works from 20 to 26mm monitor thickness. ... you need to print: 1X Microphone_Stand_tiny_60%_wide 2X screw_and_knurled_knobHD_tiny_60% 2X clamp_protector_tiny_60 % Backlight:...
3docean
Vintage Mounted Microphone .................................................................................... Description: Vintage Mounted Microphone 3D Model created in 3ds Max 2011 and saved to 3ds Max 2010 as well & render to mental ray. Use...
thingiverse
This allows you to pop the top cover from a Monoprice monitor pole mount, replace it with this bushing, then use the bayonet mount of a boom mic to raise your boom mic OVER your monitor. Most monitor poles are the same OD, but may have different...
thingiverse
Headphone hanger that can be mounted behind your monitor.
thingiverse
Summer is coming soon ;) Getting Ready. ... PS. Mounting on the monitor Samsung SyncMaster CA450 and similar
thingiverse
Simple bashed together design for a theadset holder to be mounted on most monitors
thingiverse
This is remixed from Megahertz604 desk mounted version https://www.thingiverse.com/thing:4242885 I liked the look of it but wanted to mount it to my monitor instead. As a result I had to add some rigidity and fill in the bottom to be able to hold the...
thingiverse
It's a mash up of one of the walls from that set and a monitor made byPabloNada, with the power cables taken from the side of Curufin's Sci-fi cargo sled. ... Update: I added a second version, this one without the cables, which uses Printablescenery's...
thingiverse
This is a simple monitor mounted pen holder I designed and printed to clear up my work desk, simple to install using a strip of double sided tape. Hope you like it. Stay tuned for the ruler, calculator, post-it note remix! You can purchase...
thingiverse
I created this for a MyMiniFactory design challenge. ...I used velcro to hold it on the back of my monitor
thingiverse
This is a simple holder/organizer for pens, markers and such which mounts to your monitor with velcro or double-sided tape. It will hold three pens or markers along with 2 up-to-an-inch-wide-things. This was directly inspired by...
thingiverse
Clips in perfectly to the top vent on the back of the monitor that makes it extra stable. I use it with my Bose QC25 (should also work for QC35 ). ...Has a extra piece just inside the headphone hanger if you want to wrap your headphone cable around to...
myminifactory
UPDATE: 9-26-2018 Added a V2 option that is oriented correctly and doesn't need supports. Added rounded corners so it won't snag on things. Uses less material and NO SUPPORTS Made the eraser hole larger because it was difficult to remove. Made...
prusaprinters
(or left if you mirror it :)My headphones have a 30mm headband, so that's what this one is made for. [find enclosed the f3d file for customizing to your specs]***EDIT***I've added a new version (V24) I think it looks a lot better. has more...
thingiverse
... in there which required a notch to slide in, which can catch even more dirt. The plan was to decide when I see it in physical form but I've printed two of them already, and still undecided. Only works if the top of your monitor is 10 mm thick
thingiverse
Microphone Holder for Dual Monitor Stand use M4x30mm bolt with wing nut designed for 36mm post