monopod for magpul prs 3d models

... P100s holder_cup - designed to replace stock caps Segway P100s The stock wing bolts do not fit, they cling to the tire, I had to replace them with m4x8. ... For fixing, I used a metal clamp. ... I do not recommend plastic ties, they burst

... results. The rhythmic motion of the saw blade slicing through wood is a sound synonymous with traditional craftsmanship, evoking a sense of nostalgia for generations of skilled artisans who have relied on these versatile instruments.

To improve the LCD display, I opted for a knob instead of the original turn-and-push shaft. After printing the initial "knob" file, I discovered that the hole was too small, necessitating filing. Despite making a larger hole in the "bigger hole"...

The vase mode dice tower is neat and looks great, but in practice it was falling over for me and the dice were flying across the table. This tray helps.Also adding plaster into the bottom of the dice tower (not the tray), also helps to make it more...

... provider has. I bought simple 12V UPS module and attach 18650 battery to it. And now I have possibility to keep power on my router. There is a case for this simple device. ...Note, you will need the six nuts which should be inserted in the holes

So I opted for a remix of the t-nut generator with the customization from 'anthem'. Thanks go out to the person who shared. This T-Nut bar can be directly glued onto the part and has just enough clearance to slide the part into position along the...

The nozzle is designed for the drill (tumbler) TASP MMD 001A12. ... 3D printing options: * Plastic: ABS * Nozzle size: 0.4 mm * Layer height: 0.2 mm to 14 mm * Layer height: 0.24 mm from 14 mm to 54 mm * Printing speed: 25 mm/s to 14 mm * Printing...

... Notably, the top edge of the Cover is wider than its bottom edge. Specifically, the top edge measures about half an inch (14.7mm) while the bottom edge measures roughly a quarter of an inch (6.13mm). These dimensions are rounded for simplicity.

I added an extra part for the GREG filament manufacturer's spool in St.Petersburg, Russia, which is available at http://www.thingiverse.com/thing:3588186. I needed it because I bought a filament bobbin with a different production spool that was wider...

I was having a lot of trouble printing this as it didn't have the proper measurements to be used with the "Stand for Stando Arrow" which can be found here: https://www.thingiverse.com/thing:3881374/It's already scaled properly to be used with the...

http://www.banggood.com/100pcs-M34mm-H62-Brass-Knurl-Nuts-DIY-Accessories-p-971077.html This adapter is perfect for fine infill settings, with a resolution of 25% and no rafts or supports. It's also a great addition to any Prusa Hephestos printer,...

General descriptionThe adapter is mainly created for use with a peristaltic pump, where I didn´t want to press the power button of the screwdriver for a while to keep constant speed.Using the adapter allows to adjust speed to your needs by rotating...

I've managed to track down replacement motors for my Propel X-Wing and Propel TieFighter model, but these motors are too small to fit snugly into the housing of the RC models. As a result, I decided to design a spacer that the motor can fit into...

Space-saving bracket for the motorcycle helmet The helmet holder is ideal for small spaces. It offers a convenient place to store the motorcycle helmet and is mounted on the wall completely uncomplicated. Compared to a motorcycle helmet lying...

13-06-21Truck MPCNC PRIMO FOR NEMA23Designed this from start to use my Nema 23 motors and made it as solid as i could.Im attaching the Fusion360 FileNo Need to RENAME only if file doesnt open in Fusion360(f3z file is not allowd to be uploaded so...

13-06-21Truck MPCNC PRIMO FOR NEMA23Designed this from start to use my Nema 23 motors and made it as solid as i could.Im attaching the Fusion360 FileNo Need to RENAME only if file doesnt open in Fusion360(f3z file is not allowd to be uploaded so...

It displays this grid one layer at a time for easier creation of Minecraft sculptures from STL files, serving its primary purpose. In OpenSCAD, you'll find the instructions. ...Note that to open the STL in OpenSCAD, it is advisable to process it through...

... holder with the bigger dice compartment doesn't fit anymore, so i created new boxes with 0.25mm gap to work around this... Attention: The small box is only for the new one "Paleo_Rangement_Token_3_18mm" (Updated 01-09-2022) from Lilian_Patate!

... The entering channels crossing forms the cavity to allow colors to mix. Keeping filaments separated as far as possible reduce the hysteresis and there for filament waste, when the sharp color change is needed. ... Category: 3D Printer Extruders

This project involves a small servo designed to be used alongside HeaterMeter 4.0, employing an SG90 Micro 9g Servo suitable for RC vehicles. The servo and aluminum rod were purchased from eBay and Home Depot respectively. An OpenSCAD file is...

Fed up with the usual screw organizer ? Why not build a simple organizer that is very useful for your girlfriend? Your girlfriend will be very grateful to you! And she will approve the purchase of a new another one 3D printer! Maybe ... ... :D</p>...

The specifications for this version are as follows: style - round thin; part gap - 0.08; part type - lid; inside diameter - 38; minimum wall thickness - 1.0; interior height - 22; top/bottom thickness - 1.0; lip height - 3.0; number of sides - 6;...

As a result, I had to carefully tap it into place several times.\r\n( Source for tapping: https://www.youtube.com/watch?v=lZQ3wQjJwxw&feature=youtu.be&t=116 / 1:56-2:02 :)\r\n\r\nIf the fit becomes too tight with your printer, settings, or personal...

... ...The entering channels crossing forms the cavity to allow colors to mix. Keeping filaments separated as far as possible reduce the hysteresis and there for filament waste, when the sharp color change is needed. Category: 3D Printer Extruders

So I designed a tiny case for the strip which has 2 planes of material on one side and acts as an diffusor. It looked much better now, but the case had a way of always falling on the back. So I designed a holder for it Print it in transparent. ...As...

... It looked much better now, but the case had a way of always falling on the back. So I designed a holder for it Print it in transparent. As usual the freeCad source is included so you can adapt the thing to your needs. Category: Outdoor & Garden

Just place the sprinkler around it without having to uproot your plant, as it is cut at an angle of 30 degrees.Video link: https://youtu.be/y1kl_0LNISUWalls of sprinkler are 2 mm thick, and it has 13 holes of 0.8 mm diameter for the spray pattern.The...

The original is from Archipel, all likes go to him please, for the great pegboard.&nbsp;Simple spacers. ...So you can freely choose which you need and also adjust it later if it was too little.<br>The wall distance from the Prusa Skadis is 10mm.<br>Ikea...

I've incorporated a notch with a 5 mm width for accommodating an USB-Powerline and drilled a hole in the button to facilitate water drainage if any enters. Please note that this alternative hasn't been thoroughly tested. New Version 22.03.20: The...

I do not know all the laser housing assembly dimensions from Endurance, I can tell you this design is for a 50mm square assembly. In my case, the 3.5 watt laser from Endurance Lasers. I assume it will work with the all the others from 2.1 watts to...