monoprice m1060 3d models
6252 3d models found related to monoprice m1060.
thingiverse
Hexa grill for Monoprice M1060 headphones. This one is improvement of v3 version, since the round frame has only circular head movements. ...Result is super smooth, No grainy top surface.
thingiverse
Mrspeakers ether style hexa grill for monoprice m1060.
thingiverse
WIP for a Closed back for the M1060 Headphone. ...Inspired by the M1060C https://www.monoprice.com/product?p_id=29513.
thingiverse
For Monoprice Monolith M1060 headphones. ...Pad side fazor plus ear pad mount.
thingiverse
A simple attachment to replace the sticky pad when mounting a ModMic microphone to the Monoprice Monolith M1060 headphones. ...It clips directly to the stock outer grill.
thingiverse
For Monoprice Monolith M1060 headphones. Fazor design used by other more expensive brands to reduce sound reflections for a smoother sound. Best used for grill side. ...Use the M1060 Fazor Pad Adapter for pad side.
thingiverse
... with tapered screw holes. ... For Monoprice Monolith M1060 headphones. Attempted to reduce amount of material blocking the drivers and to line them up to the magnetic bars and leaving the exposed diaphragm open. ...2mm thick for additional strength.
thingiverse
For Monoprice Monolith M1060 headphones. Attempted to reduce amount of material blocking the drivers and to line them up to the magnetic bars and leaving the exposed diaphragm open. 2mm thick for additional strength. ...Screw holes are not tapered so...
thingiverse
Custom designed grille for Monolith M1060 planar headphone to replace the stock stamped metal one. Stock grille weighs 15.35g, this one weighs less than 12.5g. Much more open design than stock grille and seems to sound a little smoother. ...Mainly just...
thingiverse
This design is for monolith m1060 earcups. I purchased some dekoni 110mm and they came with glue. However they didn't stick very well. Made these rings to attach them magnetically. Should work with any 110mm earcup. Print settings shouldn't...
thingiverse
These go on top of the v4.1 pad side fazors. ...You can mount various pads on this adapter including HiFiMAN pads with their clips. Sized at 100mm, you can also use HM5 pads on your M1060.
thingiverse
Likely the final revision for the M1060 fazors. Please feel free to adapt them in any way. You will need to double side tape or glue on the V4.1 Pad adapters to mount pads properly. ... Only reason these and the pad adapters are separated is because...
thingiverse
These are V1 grills. I'd recommend the V3 grills over these. ...These are only 1mm thick and don't have tapering on the screw holes.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/f6seRwR38ih
thingiverse
Revision with shorter sidewalls and removed upper and lower fazor bar for easier fitting. ...Prints two at the same time without issues to save time starting another job.
thingiverse
Variation with top and bottom pieces. ... You can download them seperately at: Top: https://www.thingiverse.com/thing:2527651 Bottom: https://www.thingiverse.com/thing:2527650
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/f6seRwR38ih
thingiverse
This is a fazor that uses Trochoid profile instead of ellipsoid or triangular cross section. ...The baffle chamber has been increased to 3mm from the previous 2mm to reduce peaks and improve midrange.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/4p6VSm8XXqJ
cults3d
I was looking for a Monoprice keychain but I couldn't find any so I decided to make my own on Openscad
thingiverse
I was looking for a Monoprice keychain but realized that there aren't any on Thingiverse so I decided to make my own on Openscad
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/lLI0yLTKJDd
thingiverse
not satisfied with the original rear fazor, I enlarged it and gave the wave guide a uniform profile for even sound propagation
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/lX5UPzAE9J7
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/f6seRwR38ih
thingiverse
Short story: My original pads began to fail me so I purchased some Dekoni leather pads as a replacement and found they subdued the low end of the headphones. I noticed that if there was a slight gap between the headphones and my head to allow air...