monoprice maker architect 3d models

This should also work with Cocoon Create or Wanhaou I3Plus as well. I wanted to install a fan duct that attaches through the rear side of the printer. The PCB was connected to one of the lower bearing blocks, so it had to be relocated. Ideally, it...

I needed brighter lighting for my printer, and my desk lamp was creating annoying shadows by pointing directly at it. I discovered some LED strips that could be wrapped around the edge of the printer frame, but the problem arose because the frame...

<p>First export of my own setup, refined with time, this setup is working very well for me, including the fan ducts.</p> <p>Feature highlight:</p> <ul> <li>TPU friendly, can print TPU at quite high speeds</li> <li>blower fan adapter for the E3Dv6,...

I recently encountered a problem with my heated build plate wire getting pinched during a large print (see photo). To prevent this issue, I created a retainer that addresses the problem effectively. To ensure a smooth printing process, lay it flat...

<p>I was using this filament guide (<a href="https://www.thingiverse.com/thing:1663067">https://www.thingiverse.com/thing:1663067</a>) which worked most of the time, but on new rolls of filament it sometimes pulled the filament over the reel to where...

These feet eliminate vibrations transferred from your printer to the work bench/table, cutting down on noise without needing to buy a paver and a foam pad.Printed with no supports at 0.2mm layer height in PLA. You will need print 2 as is, and then...

I was utilizing a different filament guide which functioned well most of the time, but with new rolls of filament it sometimes pulled the filament over the reel, causing it to get stuck on the holder. The printer head could also collide with the...

Footwear suppressors

**WRITE-UP IN PROGRESS (11/27/2017)** Current inspiration is derived from one mount I discovered here - https://www.thingiverse.com/thing:2016128 I sought the ability to turn my laser on and off with a toggle switch due to using the cooling fan for...

The structure features 1mm thick Polycarbonate sheets, precisely positioned within a sturdy frame composed of four distinct components. Strategically placed magnets, measuring 10x3mm, serve as optional attachments that can be securely screwed into...

UPDATE 14/06/2018: Version 2 of this make now includes a terminal bracket intended to be mounted above the extruder on the uppermost bearing block screws - this arrangement completely eliminates any lateral force at the point where the filament...

Attach this clip to the z-axis so that it triggers the z-endstop before printing begins.

UPDATE! 5/25/2018 - I've just added a modified version that's 2mm farther from the bed to dodge any pesky printed threads and other obstacles. THIS IS UNTESTED, so be prepared for anything. I'm eager to hear your thoughts on this modification. I...

This is a fanduct which replaces the poor stock mainboard cooling solution. I designed the fan mount for a EBM-Papst RLF 35-5/14N. I can cusotmize this mount if you like. The exausts for the X and Y stepper driver are larger due to the reason I have...

I resized the back plate to fit my z-brace mod, shortening it and reversing it in case I had routed cables to the opposite side. To secure it, I filled in screw holes on each side instead of using double-sided tape. You may need to enlarge the hole...

I'm remixing the original design from https://www.thingiverse.com/thing:2869616 by te311909. I ditched the scraper hook since I upgraded to a PEI bed. ...This holder is compatible with Z Brace Mod and works seamlessly alongside a same-side Meanwell...

Remix of Card Holder for Wanhao D6. This holds the board that the ribbon cable plugs into, with added length and a support across the middle for a more secure fit when using my Cable Holder from Thingiverse:...

I picked up some 6 inch metal rulers from Amazon. You can stick them to your frame with double tape, but I chose small coin-sized magnets so I could reposition them as needed. ... You'll need to replace the screws on your metal rod - specifically four...

The cooling system fits snugly between the fan and the extruder.

I reinforced the entrance by installing an additional wall panel to conceal most of the electrical infrastructure.

There are quite a few sensor mounts that either don't fit 18mm sensors without modifications or require aftermarket cooling. Typically, I use a glass bed and test out an 18mm capacitive sensor for auto-leveling, but I haven't done enough testing to...

I've found the original fan mount clips a real nuisance and any attempt to fiddle with the hot end is a major pain. I desperately needed a way to quickly remove the part cooler and adjust for different height tips, which was largely driven by my...

Logicfail's Tool Holder was revamped, and a nodge was cleverly incorporated into the Scraper Holder design.

These feet eliminate vibrations transferred from your printer to the work bench/table, cutting down on noise without needing to buy a paver and a foam pad.Printed with no supports at 0.2mm layer height in PLA. ...You will need print 2 as is, and then...

Thanks to CarstenD for the original file, I've added a cable chain mount to it so that screw can be securely fastened back on. The offset of the bracket might need to be adjusted - I'll print and test it tonight. ...A Bowden e3d v6 mount has been...

I lost the diminutive screw for my Wanhao Duplicator 6 control push button, so it started to fall off most of the time. I tried to find a ready alternative but the only one I found was quite complex to print so I created my own easy-to-print...

This is a sleeve case combined with a mounting plate to fit on the right side of the printer.

I was determined to install my spool on the side rather than the top, thereby preventing any potential jarring of my printer, but then I faced a challenge in directing the filament smoothly towards the extruder. ...To resolve this issue, I removed two...

Simple filament guide I designed specifically for placement atop the z-gantry. Two 608 or ABEC 7 bearings are required. ... UPDATE 02/06/18: Due to the fact that this does not resolve extrusion issues when filament is mounted to the side of the...