monoprice maker select v2 cura profile 3d models

This is a spinner for Monoprice Select Mini

The Monoprice Maker Select Pro is now equipped with a custom Raspberry Pi camera mount, expertly reimagined from the original 2020 Extrusions design. ...I meticulously assembled it using precise M2.5 screws and extended the Pi camera cable to an...

This profile was printed using Marlin 1.1.8 firmware (available at http://www.customize-3d.com/tech/flashing-tronxy-x5s-factory-control-board-usb-cable-only.html) after I had tuned both the bed and hotend for optimal performance. ...The prints were...

... The files are version 4.0.0 and I use the "Sidebar GUI" plugin. If you're using a higher version like 4.4.0, some options won't work even though they're selected. In that case, just deselect them and then reselect them. ... Have a great print!

I wanted a movable guide for the filament on my Monoprice Select Mini V2. I have printed and used the small guide with the movable guide bushing quite successfully, but wanted something with more than one screw hole holding it to the printer. The...

1kg Spool Holder for Monoprice MP Cadet. This custom spool holder replaces the factory one, utilizing original removed hardware. ... Updated on 2/24/19: A new spool hanger was added with a wide taper at the end to prevent the spool from falling off...

The files are version 4.0.0 and I use the "Sidebar GUI" plugin If you use them with higher versions such as 4.4.0, some options do not work even if they are selected. In that case you have to deselect them and then reselect them. ... have a nice print ...

I had to scale down the size of the object to 87.5 percent in order to accommodate my Monoprice Select Mini's 120mm x 120mm build platform. ... Also, I've included both the .gcode and .3mf Cura project files if you'd like to make any custom adjustments.

Some spools do not fit inside the Maker Ultimate 2, so designed these in Tinkercad to support a pipe holding the spools above the printer. Print 2 spool holders and 2 braces. The braces go in the printer above the top rail, and below the case. You...

This replacement carriage is designed specifically for the Monoprice Select Mini V1 and V2, replacing the original plastic X-Axis assembly. The new design incorporates a built-in hot end mount inspired by E3Dv6, allowing for improved print quality...

Print Settings: Printer: Monoprice Maker Select Mini Rafts: Doesn't Matter Supports: No Notes: To achieve optimal results, print this part vertically. The lack of supports will not only simplify the printing process but also ensure that the print...

This here holds the 1.5, 2, 2.5, 3, and 4mm hex wrenches that came with my Maker Select. Requires: (4) M3x10 hex bolt socket machine screws are necessary to complete this project. ... Updates: (v2) I corrected the curvature of the hex wrench at the...

Print Settings: Printer: Monoprice Maker Select Rafts: No Supports: No Resolution: .1 Infill: 100% Notes: Since this tiny thing is so compact, I slowed down all my speeds, printed two at once, and used a 2mm brim. And no worries about the i3 on the...

The perfect accessory for your Monoprice Maker Select is a 2-piece glue-together holder that securely stores all five pieces of the allen wrench set. Allen Wrench Set Sizes: • 4.0mm: This is the largest size in the set, measuring from flat to flat....

This is a remix of a few things for the Monoprice Select Mini, it works on my V2 and should work on the V1 and Pro. Print flat on the “back” and use buildplate supports. I printed at 35% infill and .2 in PLA and it seems just fine. Fits the Lanmu...

Monoprice Select Plus 3D Printer Spool Holder The spool carrier is an essential accessory for the Monoprice Select Plus 3D printer, as it helps keep your filament organized and tangle-free during printing. This holder securely holds your spool in...

This is a substitute X-axis termination piece designed specifically for the Monoprice Select Mini 3D printer.

This is a powerful spinning tool for Monoprice Select Mini, crafted to bring out its full potential.

I had to find a solution to secure the control box to my enclosure's lower cabinet, but since I hadn't used a LACK or Mainstays table for my build, and my lower cabinet features drawers, none of the available options would suit my requirements. ...To...

TLDR: Stock limit switches are a pain. Replace Y and Z switches using this adapter. Parts listed below. You'll need a soldering iron. One day I started a print when I heard the awful noise of my Y axis motor grinding my build plate against the...

This custom-built case is specifically tailored to meet the builder's unique requirements. Constructed as a direct response to the issue of a PSU being too long, I created it to avoid mounting it externally. The original design for my mini-case was...

So the other day, I was printing something that required the extruder to move left and right rapidly, when I noticed that the belt had a significant twist in it. This problem occurred because the pulleys weren't parallel with each other. I discovered...

I just scored a Duplicator 2.1 from Microcenter and I'm checking out all the awesome mods available. This one caught my eye, but I've heard it produces a bad hum. I'd like to try increasing the surface area to minimize the humming noise while keeping...

This design is created using Tinkercad's powerful online editor. ...Make adjustments and tweaks directly on the website at https://www.tinkercad.com/things/8cKrNosHN53.

This DIY extruder replaces the original hot end without requiring a separate purchase. Like many similar alternatives, it necessitates a bearing and a nut accompanied by a bolt. A 1/4-inch aluminum tube for the final few inches leading into the hot...

It was time to say goodbye: The ear-piercing screech of the worn-out X axis LM8LUU bearings had to go. So I designed bearing blocks for the upper and lower X axis that use 2 LM8UU Igus Drylin bearings end-to-end in the sleeve, held securely by...

This adapter mounts the MKS Gen V1.4 board into the original Wanhao Duplicator i3 control box, providing mounting points for a MOSFET with 52mmx42mm hole spacing like the BIQU power module expansion. The design fits around existing Melzi standoffs...

Attach two skateboard bearings directly to the rods.\r\n\r\nFirst, slip the cylinder into place within the spool before adding the roller.\r\n\r\nFortunately, I found that the bearing fit snugly without needing the pin originally intended for this...

This is a zero offset adapter for an E3D hot end clone found at Amazon.com. I opted to utilize the existing hot end carriage because it's made of steel, and can withstand heat better, plus it already comes equipped with a parts cooling fan. This...

This is an adapter to mount the MKS Gen V1.4 board into the original Wanhao Duplicator i3 control box. It also has mounting points for a MOSFET with 52mmx42mm hole spacing such as the BIQU. It fits around the existing Melzi standoffs, and can be held...