monoprice mini delta 3d models
100150 3d models found related to monoprice mini delta.thingiverse
This is a foot for a Monoprice Mini Delta. It helps to increase airflow under the printer. ...It also helps to reduce the volume of the fan.
thingiverse
Attachments for the Monoprice Mini Delta printer to be able to stack the printers vertically. The feet need to be installed first on the top and bottom with the screws already on the printer and M3 screws and nuts are used to attach the printers...
thingiverse
Stock linear bb replacement for monoprice mini delta printer. ... This is hot-press fit part , so you must take the rod off the printer and using heat gun or stove bring it to 120-150C and than press bb on it
thingiverse
This is a spindle spacer that complements the Monoprice Mini Delta Spindle Rounder by rezin8. ...
cults3d
Files and instructions for the sides I made for my monoprice mini delta printer.
thingiverse
Files and instructions for the sides I made for my monoprice mini delta printer.
thingiverse
Magnetic Screen Blind for Monoprice Mini Delta Required: - Magnets: 2x 10mm diameter. ... - Some glue ;)
thingiverse
Clips onto the side of any side of the Monoprice Mini Delta
thingiverse
Monoprice Mini Delta Top Spool Holder Can be printed on the Mini Delta due to the part been split I used this with the below filament adapter: Customizable spool adapter by RomanoLindano inner = 21; outer = 58; wall = 2; deep = 50;
thingiverse
There are many interesting knobs for extruders. ...I adapted several of them for the stock extruder Monoprice Mini Delta. ... You print, put on the extruder motor shaft and see how it works.
prusaprinters
Nobody has to guess which button is left or right anymore...You can print all 3 buttons (2 x Arrow, 1 x Enter) in your MonoPrice Mini Delta in one go, just line them up in CURA. If you want the dual colors like in the picture all you have to do is...
thingiverse
You can print all 3 buttons (2 x Arrow, 1 x Enter) in your MonoPrice Mini Delta in one go, just line them up in CURA. If you want the dual colors like in the picture all you have to do is pause the print halfway and switch the filament. ... To glue...
thingiverse
I didn't like the sharp edges of the bent metal spool holder on the Monoprice Mini Delta, so I modelled this up that slips over the spool holder and gives it a nice 26.5mm radius on the spindle. Should smooth out feeding of filament. ... Inspired by...
thingiverse
This is a replacement for the stock hotend fan shroud for the Monoprice Mini Delta. Its not a perfect replica, but is fairly close. I left a bit more room for the heater cartridge, which I had initially melted a bit of the stock one when I was...
thingiverse
A simple mounting bracket for a cooling fan for the Monoprice Mini Delta. The CAD is parametric with default settings for a 120mm fan, which is a good fit anyway. Print four of the parts, insert them into the channels on one of the open sides of...
prusaprinters
Magnetic Screen Blind for Monoprice Mini Delta Required: Magnets: 2x 10mm diameter. Some glue ;) Print Settings Printer Brand: Monoprice Printer: Mini Delta Rafts: No Supports: No Resolution: 0.2 Infill: 15% Filament: Devil Design PLA Blue ...
thingiverse
This is a snap-in leg shield for the monoprice mini delta. It prevents debris from falling into the body of the unit from the build chamber. It snaps into the channels in the chassis and is as short as possible so as not to interfere with the drive...
thingiverse
BUT NONE OF THE PICTURES SEEM TO BE SHOWING* This is a simple option for lighting on the Monoprice Mini Delta that I whipped up on Tinkercad.. For this to work you're going to need to buy two things 1.) 5w USB powered Light (buy two if you want...
thingiverse
These will hold a 120mm glass plate on the bed of your monoprice mini delta quite securely. You also get some nifty shields that prevent debris from falling into the bottom of your printer. This is a remix of 2 good designs on Thingiverse and I...
thingiverse
I wanted to make an enclosure for my delta, and had some free acrylic to work with. I designed this and printed a total of 6, two for each space. The sides rest in the slot allowing the 8mm thick acrylic to slide either way, and be removed easily. I...
thingiverse
Adapter for a 4020 blower fan for the Monoprice Mini Delta. ...Requires one 20mm M3 screw and nut to assemble.
thingiverse
A side clip for the Monoprice Mini Delta suitable for attaching the "Raspberry Pi Camera v2 Universal Mount".
thingiverse
Top mounted spool holder for the Monoprice Mini Delta. ... Based on this project: https://www.thingiverse.com/thing:3459636
thingiverse
This is a remix of 1ProjectAWeek's PS Eye Cam Mount. ... I modified it to mount on the bottom part of the Monoprice Mini Delta.
thingiverse
This is a hook to mount on top of your Monoprice Mini Delta 3D printer so that your blue painter's tape is always handy.
thingiverse
Filament Reel extension for the Monoprice Mini Delta. The two pieces slide on the stock reel holder. ...The 608 bearings press fit onto the pieces.
thingiverse
This is a hook to mount on top of your Monoprice Mini Delta 3D printer to keep the plastic spatula that came with it from getting lost.
thingiverse
I found a similar one (2690867 MP Mini Spool holder bearing by NbJosh), but the dimensions were too large for my printer. ...this will fit the Monoprice Mini Delta spool holder measuring 19 mm x 22 mm. ...Uses 608 bearings.
thingiverse
Filament guide for Monoprice Mini Delta remixed to have filament exit from spool more linear. ... Latest STL is a little better .printing it 4-5% bigger helps get the Teflon tubing in easier , or you can sand down the tubing.