mortise lock conversion to standard 3d models
2124187 3d models found related to mortise lock conversion to standard.thingiverse
If your mortise lock/latch is the style that just has the latch and not a lock you may only have round trim pieces on either side surrounding the doorknob, if thats the case then you don't need the trim plates, in my case the door had another large...
thingiverse
Converts olympic size weights to fit a standard 1" dumbell or bar. The sizes are set to fit the Fitness Gear brand plates. I use the weights on an olympic bar as well so I didn't want the rings to be hard to remove. These slip in and out easily...
thingiverse
Just finished my Mortise Lock. I drew it in 3D, but didn't designed/invent it, and printed it out. You can see the full function here: https://youtu.be/t5RI16ncwFA Hope you like it. ... Layer: 0,2mm Infill: 50% Speed: 40mm/s
thingiverse
Mortise lock based on 60's lock taken from old door. All parts included except springs. ...Includes skp files for Sketchup 2017.
grabcad
Just Finished my homework today and was wandering to make something, I saw this lock fixed at my room door and tried to make it just identical to the real one but... as always, Still learning!! ...I is not for nerds looking for the prefect mechanisms...
thingiverse
Makes it a little easier to hold a standard mortise lock in your hand for practice picking. Reduces the strain and wear on your hands from the screw threads and various cuts in the metal and increases the diameter of the cylinder, making it easier to...
prusaprinters
Turns out I had several different mortise locks with different keyhole spacing so have uploaded two sizes. FYI…Just barely fits a Mini build-plate so make sure your first layer is spot on a maybe bump up the plate temp a bit to help with...
thingiverse
It uses a standard m3 x 0.5 trapped nut, and you can use a standard m3 screw, or a thumb screw, as pictured, for tool-free removal of the lock. I originally printed this in PLA, but I would like to try it in TPU for maximum comfort. ... Made in...
thingiverse
This is a simple print to demonstrate the Burg-Wächter ME "mortise lock", a.k.a. "stealth lock". This lock module has been used for a long time for....kinky applications, but I think its versatility lends itself to all sorts of practical uses! The...
grabcad
Just new conceptual design of handle used for mortise lock. Bottom of holding area made up of semi circular profile will help for better ergonomics. ...Good look with multi tones of material..
thingiverse
All parts of the stand are included for you to mix, match, and remix as you please :) *All dimensions were measured after print* 6 pin stand: Height: 31.5mm Width: 35.5mm Length: 46.75mm Lock Holding Area Length: 30.5mm 7 pin stand: Height: 31.5mm...
thingiverse
Our house has some french doors with mortise locks, and as the house has shifted over time, the doors have parted so they wouldn't latch closed. This mod extends and offsets the strike plate so the latch will close. ...(v8 update rounds the exposed...
grabcad
Hi guys, This is my first upload (Mortise door lock) our local model, It is very simple Model not an insider maybe later be more detailed version. Hope cut who need it some time. ... the version of solidworks is 2015 not 2014 enjoy.
thingiverse
... I wanted to put in was 32mm not the usual 29. ...I scaled the whole model up in X and Y to fit the lock, and scaled it down in Z to make it shorter and print faster. ...Done in TPU, the lock slides in snug enough to not rotate and needs no fastening.
thingiverse
The design was inspired by https://www.thingiverse.com/thing:3385722 which appeared to be too small to fit this mortise lock, as well as a bit too small to hold comfortably for me, and https://www.thingiverse.com/thing:3115194 which felt good in the...
thingiverse
[For details and most recent files please see PrusaPrinters.org](https://www.prusaprinters.org/prints/67406-whisper-trap-for-mortise-lock)
thingiverse
Mogul Mortise lock display stand Mortise Width: 2 inches All parts of the stand are included for you to mix, match, and remix as you please :) *All dimensions were measured after print* ------------------------------ More lock display models...
thingiverse
This is a dead-drop spike designed to use the Burg-Wächter ME "mortise lock", a.k.a. "stealth lock". This lock module has been used for a long time for....kinky applications, but I think its versatility lends itself to all sorts of practical uses! I...
thingiverse
This is a Ditto-shaped lockbox designed to use the Burg-Wächter ME "mortise lock", a.k.a. "stealth lock". This lock module has been used for a long time for....kinky applications, but I think its versatility lends itself to all sorts of practical...
grabcad
Parts to convert a Plazma LM to standard wheelbase. If you have a full Plazma LM, you'll only need the main plate. The other parts were for building a car piecemeal with spares without using the battery holder. Front suspension and servo mounts are...
prusaprinters
This applied to the standard version, not the heavy or Phasma variants.https://www.whitearmor.net/forum/topic/45171-first-order-f-11ds-the-force-awakens/Research thread is here:...
thingiverse
These are parts for a 100-year old mortise lock by Russwin -- the Russwin P1213. You can read more about the lock and how I've been restoring it here: https://hackaday.io/project/174603-this-old-lock I originally printed these in PETG and they...
thingiverse
... on this final design; if there is any interest I can link to the parametric model so that you can customize as needed. ...I have not found this necessary, as the internal cylinder diameter can accommodate all the locks in my personal collection.
thingiverse
This is a remix of the bottle lock, designed to use the Burg-Wächter ME "mortise lock", a.k.a. "stealth lock". This lock module has been used for a long time for....kinky applications, but I think its versatility lends itself to all sorts of...
thingiverse
A coupler device to interconnect an International Standard ink converter to any regular luer lock blunt nose needle
thingiverse
This is a holder for standard 29mm mortise locks for handheld picking. It is designed to be printed using soft TPU with 20% infill to make it nice and comfortable to hold. Have fun with it! Edit: I added a 31mm mortise lock version. Some older...