moto x first gen case 3d models
668805 3d models found related to moto x first gen case.thingiverse
A phone case for a Motorola Moto X, 4th generation phone. Does not incl a screen protection. Printed ; - PLA, @ 218 C - .2 layer height - no supports Clipped on the ends only so slide one end in first, bend a little and push other end in. ... enjoy
grabcad
The first generation of motorola moto g, personal hobby project, the ensemble consists of five parts, the body, the back cover, the front glass, glass camera and screen ....
thingiverse
A clean, simple case for your Moto X. Instructions For best results, print with raft and supports then wipe down finished model with a little acetone once supports have been removed. To put the case...
thingiverse
This is a cell phone case for the Motorola Moto X I have included a screen protecting cover as well. ...Printed on a Makergear m2 Layer height .150mm
thingiverse
This is a modified version of the Moto X Case v2.0 by andrewSORG. I raised the edges to give the screen protection, so that if it's dropped screen down, the case, not the phone hits. For 1st Gen only. Print Settings Printer Brand: ...
thingiverse
This is a remix of http://www.thingiverse.com/thing:270209 Adapted for Moto X 2014 version. -- The case has been slighty resized as per d979bdf2 findings. ...It snaps onto place properly now.
thingiverse
Moto X 1st gen (XT1058) Stand & USB dock charger. (Might work with similar phones) Photos are not of the exact same model, the one I uploaded is a revision, should work better! ... PS: Had to glue the micro usb to the dock in order to prevent...
thingiverse
Designed a desktop stand for my new Moto X 2nd gen. And now you can print one too! Prints in 2 parts + right angle USB cable. Instructions Print both TOP and BOTTOM pieces at a decent resolution. ...
thingiverse
I ever-so-slightly adjusted the 3D model to better fit the Moto G 2nd Gen phone (after printing), so technically the uploaded case is untested. But you'll see in the photo that It should hold the phone fairly securely, better than pictured. Feel free...
thingiverse
THIS THING IS WORK IN PROGRESS. ...v1 was just a bit too short, so v2 should work Is there a Moto G3 case? ...I didn't found one so I remixed a G4 Play case from Nipsel.
thingiverse
Instructions Change the following options in the Customizer: Printer Tolerance = 0.2 Use Custom Dimensions = On Custom Phone Width = 72.4 Custom Phone Length = 142.1 Custom Phone Thickness = 11.6 Custom Case Pattern Thickness = 1.6 Custom Back...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=507810 Instructions Using the following options: stencil_rotation = 0 custom_back_extra_port_corner_radius = 0 custom_bottom_port_x_position = 0 stencil_pattern_element_radius = 6...
thingiverse
I didn't like the pixel XL cases currently on Thingiverse, so I designed my own. Designed for TPU (Ninjaflex). Phone will not be able to be put in the case if not printed in flexible material. ... Will likely need suports for the inside top &...
thingiverse
An improvement on my previous Moto X case, this version has 3 major changes: Easier to print (no longer needs raft or supports.) Easier to get on and off your phone. Better access to the side buttons. Plus, I've uploaded a couple of .IGS files...
thingiverse
Want try print it with flexible filament later. ... Case w/o headphones hole, i don't use it. ... The phone is inserted with effort if hard filament use.
cults3d
For other phone cases check this. Here is the explanation of the files names: Flex: made for elastic filaments like TPU. Tested on TPU. Rigid: made for rigid (non-elastic) filaments like PLA, ABS, HIPS, etc. The entire model is a little bigger and...
thingiverse
If you have any request on the design just ask me. For other phone cases check this. Here is the explanation of the files names: Flex: made for elastic filaments like TPU. Tested on TPU.</li> <li><b>Rigid:</b> made for rigid (non-elastic)...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1655546 Instructions Using the following options: phone_depth = 1.8 offset = 0 support = 0 phone_thickness = 12 extraD = 0 phone_width = 74 connector_width = 19 TextLabel = Alexis...
thingiverse
Customized version of http://www.thingiverse.com/thing:1475333 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1475333
cgtrader
This is a cell phone case for the Motorola Moto X I have included a screen protecting cover as well. ...Printed on a Makergear m2 Layer height .150mm
thingiverse
Customized version of http://www.thingiverse.com/thing:33345 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=33345 Instructions Using the following options:...
thingiverse
stand to hold the phone more flat timelaps:https://youtu.be/z3L_AaqDdNk