motorized pulley 3d models

Motor Pulley

MOTOR PULLEY OF MILLING MACHINE

Just a motor pulley 30mm hole is 6mm

this motor pulley is make for unigraphics nx

its a pulley system piece

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: nut_angle = 120 idler = 0 m3_nut_depth = 2.7 m3_nut_hex = 1 additional_tooth_depth = 0 idler_ht = 1.5 m3_dia = 3.2 teeth = 32 profile = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options: retainer_height = 1.5 screw_profile = 4 motor_shaft_diameter = 3 number_of_teeth = 20 screws_disposition = 2 nut_shaft_distance = 1.2 belt_idler...

this is the motor pulley of the 7x10" china lathe

This is a 3D-printable motor pulley to replace the stock one on a Dreaming Robots Electric Eel Wheel Nano. It'll work with either the v1.0 or v1.1 motor, and you may need a drop of CA glue to secure it to the motor shaft. ... This is the pulley that I...

A standard motor pulley for T2.5 belts. 16 teeth, so works as a drop-in replacement for a 8-tooth T5 pulley. Some say that this part is a vitamin, but I didn't believe them. I printed this with 0.35 nozzle, 0.20 layers, 0.36 tracks and 10 secs per...

MOTOR PULLEY 44T 196.08PCD

this motor pulley is make for unigraphics nx

28BYJ-48 Stepper Motor Pulley Made in tinkerCAD from: https://www.thingiverse.com/thing:682418/ https://www.thingiverse.com/thing:4817279

Ferris wheel with motor pulley. You can use it with Arduino and test a simple code to move the wheel! Have fun! ...

Original belt cannot be used, the belt need for using this motor pulley is: Belt: 243-3M-15 Belt cover needed: https://goo.gl/fMyX22 The belt used on the images is only 10mm wide since Ebay sent me the wrong ones, it is designed for 15mm wide belts...

I used this pulley to wind a string using a stepper motor. ...28byj-48 model stepper.

Use this pulley on your polargraph machine to connect your pen to the motors using fishing line

The pulley can be fastened to the motor by an M3 screw (picture 3) and an M3 Nut. There is a small pocket to insert the nut in the bore of the pulley (picture 2). This way you dont need to rely on the strength of a thread cut into the pulley itself...

For FRC teams that use a window motor, the adaptor shipped with them is not always useful. ...This joins the Denso adaptor to a 5 mm GT 13 tooth pulley allowing the window motor to directly drive a belt.

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: motor_shaft = 6 nut_angle = 90 m3_dia = 3.1 m3_nut_hex = 1 profile = 3 additional_tooth_depth = 0.1 m3_nut_flats = 5.45 pulley_t_ht = 11 idler_ht...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: no_of_nuts = 1 m3_nut_hex = 1 idler = 0 additional_tooth_depth = 1 additional_tooth_width = 0.2 retainer_ht = 1 pulley_b_ht = 8 nut_angle = 90...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: idler = 5 motor_shaft = 6 m3_dia = 3.2 additional_tooth_depth = 0 nut_angle = 90 nut_shaft_distance = 1.2 pulley_t_ht = 17 no_of_nuts = 1...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: idler = 1 motor_shaft = 3.7 additional_tooth_depth = .1 m3_dia = 3.4 nut_shaft_distance = 1.5 pulley_t_ht = 7 nut_angle = 90 no_of_nuts = 1...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: m3_nut_hex = 1 pulley_b_ht = 8 idler_ht = 1.5 teeth = 15 pulley_b_dia = 17 m3_nut_flats = 5.7 nut_angle = 90 m3_dia = 3.2 additional_tooth_depth =...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: profile = 1 motor_shaft = 3.4 pulley_b_ht = 8 retainer_ht = 1.5 retainer = 1 m3_nut_depth = 2.7 m3_dia = 3.2 no_of_nuts = 1 nut_shaft_distance =...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: idler = 0 m3_nut_flats = 0 retainer_ht = 0.5 nut_angle = 90 additional_tooth_width = 0.2 retainer = 1 m3_nut_hex = 0 teeth = 12 idler_ht = 1.5...

* HOLE DIAMETER = 40MM* M6 TAP FOR TIGHTENING PULLEY WITH SHAFT* MATERIAL: ALLOY STEEL

The Pulley broke so I redesigned it. Works perfectly...at least in a short testing. Enduring test starts with my wife tomorrow ;) Nachdem sich die Bürste aufgrund von zu vielen Haaren nicht mehr drehen lies, d.h. sie war komplett festgesetzt an...

http://www.thingiverse.com/apps/customizer/run?thing_id=1013153 Instructions Using the following options: RimWidth = 1.5 HoleDiameter = 8.0 idler_height = 1.5 nut_shaft_distance = 2.0 RimHeight = 7 HoleClearance = 0.1 screws_disposition = 3...

Customized version of http://www.thingiverse.com/thing:175044 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=175044