motorola stand 3d models
149955 3d models found related to motorola stand.thingiverse
Customized version of http://www.thingiverse.com/thing:1817011 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1817011 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:3577763 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3577763
thingiverse
This is a mask holder, that you can put together. Use electric tape to make it more firm, or you can glue all the parts together. I prefer the first solution because I can put it away when not in use, but if you are going leave it in a single place...
thingiverse
Remixed from TheSkullMeister to fix imperial to metric issue, and make it printable without the need for complex support. Plain base, or with AA battery tray. Fits Xbox One/XBox 360 controllers. Might fit others, don't have any to test. This is...
thingiverse
Customized version of https://www.thingiverse.com/thing:3475867 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3475867
thingiverse
This thing was made with Tinkercad. ...Edit it online https://v1.tinkercad.com/things/5cMymZPxLLg
thingiverse
Can be printed on a 200x200 bed by turning the "rod" piece 45 degrees. Make sure to rotate the rod to sit on its flat side!!! Printed with ABS, Extruder - 215c Heatbed - 65c gave good results. Make sure to get your bed level and adhesion correct;...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://v1.tinkercad.com/things/5cMymZPxLLg
thingiverse
I found out that it is very hard to get off the build plate, i would recommend using a raft.
thingiverse
This is a remix of one I found for 88g CO2 cartridges, but since I'm running 95g cartridges I redid that one to accommodate a Fluval 95g cartridge (others should fit as well). I also didn't want it too tall and cut off the top half and left the hex...
thingiverse
I designed this for my TASCAM DR-07X Linear PCM recorder. It kept falling over, and I kept forgetting to bring my earplugs to jam, so this kills two birds with one stone. It's also a quick print. ... I'd recommend painting a thin layer of...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://v1.tinkercad.com/things/5cMymZPxLLg
thingiverse
Holds the speakers at a 15 degree angle. Print left and right and join with glue, if you have better joinery suggestions please comment or simply modify and remix. I printed the first one at 10% infill, I think maybe it should be a bit more. ...The...
thingiverse
Customized version of http://www.thingiverse.com/thing:582704 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=582704 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:1720245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1720245
thingiverse
Customized version of https://www.thingiverse.com/thing:1691620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1691620
thingiverse
Customized version of https://www.thingiverse.com/thing:1691620 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1691620
thingiverse
I made 2 of those for my first Underwater shoot. I needed my Eintein strobes to be just at the level of the water so I made those. The long leg is to help balance the heavier front of the Flash. And the top stud is sized to take the regular stobe...
thingiverse
Nose wheel leg/Trailer Jockey Wheel for RC Car Trailer 3 x 40mm bolt V2 3 x 50mm bolt
thingiverse
A general tablet, which should be compatible with most tablets. I made mine specifically for an iPad 3. ...I hope to give it more functionality in the future, such as having a holder for a stylus or keyboard.
thingiverse
Simple bulborb from the Pikmin games. ...Model based on bulborb from Pikmin 3 and made to scale with Agatsuma miniatures.
cults3d
A 510 holder to store tanks or rda, Rdta, rta. Mickey themed very simple but my first design. Make sure to lay it flat when printing with hole on top. ...I am using cura 2.4 to slice