motorola stand 3d models

I took bolbot's slick missile and shortened it into a general purpose bomb with fins that might be seen in a military munitions storage area, flightline, or aircraft hangar. It would not be flown on an aircraft as is, it is more representative of a...

Just got my ODROID-GO Advance, and I made a minimalisticstand for it. ... This is a quick and easy print.

Customized version of https://www.thingiverse.com/thing:2477998 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2477998

A challenge coin display for military Makers or anyone else who collects these coins. Holds approx. 25 coins. First row is 1mm wider for thicker coins. Measures 9'' x 7'', or 22.9cm x 17.6cm if you're a communist. Included in the files is a 4-part...

I designed this Challenge Coin Holder to sit on a desk and display your challenge coin, without the holder really being seen when looking strait at it. The edge of the coin rests on the small bottom lip and sits at about a 30 degree angle. Sorry I...

Fits a 45mm wrist watch. In order to give it some heft you can glue some weights (e.g. ...coins) into the recess in the bottom.

Customized version of http://www.thingiverse.com/thing:512350 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=512350 Instructions Using the following options:...

So all the cool kids these days are creating these animated GIF things so why should they have all the fun right? So we decided to jump in both feet first and so time-lapse GIFs however we want to do them in portrait ordination rather then landscape...

Hot type bevel gear gearbox used to reduce the speed of a motor of DC Motor "ABB" 600A . It is composed of bevel gears and straight gears. ...This model was created by a team wish i was part of it.

Print flat recommended 6 outer layers infill around 20-30% slide together or glue op to you. ... A like is appreciated when downloaded.

Ideal for the phone HUAWEI P10 lite with gel case. ... I have glued a lead weight to stabilize

SummaryUse a bit of glue.Print SettingsPrinter: Prusa i3Infill: 0,15

This is my Beta Page for my different Versions of Work in Progress. ... This version is incomplete

Customized version of https://www.thingiverse.com/thing:2246209 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2246209

Holds your tablet with a tasteful Samsung logo! ...Print in PLA or it warps :(

Customized version of http://www.thingiverse.com/thing:512350 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=512350 Instructions Using the following options:...

Just select which one you like the most and print away. ... Just print them on its side with support

Custom proHeSa Logo

Materials : SPLA filament 1.75 (Heat-resistance PLA filament) Nozzle : 0.2 , infill : 10% extruder temperature : 200 Speed :.80s Size : 88 x 85 x 89 (mm)

300 micron

Phone charging dock. It was made to fit Type C cable. Little bit of hot glue will be needed for securing cable in place. Type C connector fits pretty snug so no glue needed there.I recommend to use sticky pads under the phone charging dock. ...That way...

Remix for my desk.

Published by 3ds Max

I found that it always which such a hassle to always have to look after my vaporizer, where did I put it ?!? And that it often falls down after you smoke .  So I built this simple holder ! Enjoy! ...:)

- The link to the siding model is [here](https://www.thingiverse.com/thing:5252145)(You have to choose the 200x200 version). ... - The picture shows the 5th generation of apple watch.

Customized version of http://www.thingiverse.com/thing:512350 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=512350 Instructions Using the following options:...

<p>This print uses&nbsp;</p><p>~13g of filament</p><p>m2 sized screws and standoffs to fit the holes on the raspberry pi</p><p>printed with an ender 3 pro</p><p>print speed 60mm/s</p><p>0.2 nozzle</p><p>bed temp 60c</p><p>hot end temp 200c</p>

This is a simple little item intended to display collectable guitar picks.  Image shows PLA (red), ABS (white) and HIPS (blue) prints.

Hi Guys this is my first thing!! No need for supports, but ensure that the parts are printed the correct way up. I printed this in PLA with my Flashforge Adventurer 3/MP Voxel. Its a very tight fit with the printers tolerance but holds very...