mount holder 3d models
609674 3d models found related to mount holder.cults3d
Universal cable mount/holder use a rubber band or wise wire! ... Use it on small to large cables/ multiple cables
cults3d
Simple wall mount holder for your eyeglasses / spectacles / sunglasses / shades, etc.. ...I used hot glue gun to stick it to the wall
thingiverse
Simple wall mount holder for your eyeglasses / spectacles / sunglasses / shades, etc.. ... I used hot glue gun to stick it to the wall -added a version with a hole for screw mounting
thingiverse
Universal cable mount/holder use a rubber band, Ziptie (Cable tie) or wire! ... or use it to clamp down 2 cables Use it on small to large cables/ multiple cables Mount with adhesive/nail/screw/hot glue print as is
thingiverse
Hello, SureFire Firepak fans, this is a mount/holder I designed for the Firepak, you can stick this mounting plate to any were you need, phone, car, RC model, even on the wall, apply the Scotch outdoor mounting double sided tape to the back side of...
thingiverse
DHT11 Mount / Holder I bought some DHT11 modules from amazon that were a bit longer than the ones I could find holders for so made my own. The STL has two parts, a top and a bottom. The bottom could be left out if you didnt mount the unit to...
cults3d
DHT11 Mount / Holder I bought some DHT11 modules from amazon that were a bit longer than the ones I could find holders for so made my own. The STL has two parts, a top and a bottom. The bottom could be left out if you didnt mount the unit to...
thingiverse
A wall mounted wrench holder. The rail is 140 mm long, made to be printed on my flashforge finder without supports. The pegs slide on from the sides. All parts can be printed without supports. I am only calling it a wrench wall mount, because that...
thingiverse
Simply a Mount AKA Holder with an ID of about 10mm to suit a 10mm LED or similar. Threaded to suit a hole of 16mm so you can mount in a panel for use in applications like a pc case, car dashboard etc. ... Upgraded version 2 (June 2019): Slightly...
cults3d
Guitar wall mount holder I printed it one by one then cleared the support by using drill you will need 4 screws for wall mount. they should be not more than 5mm in diameter and their cap not bigger than 8-9mm I printed and tested the files I printed...
thingiverse
Fully printable flexible arm mount item holder. Place a kindle, a cell phone or anything you like on it facing any angle at any height. Instructions Print universal_holder_set.stl to make a copy of a set. If you want to print separately, use...
myminifactory
Been thinking of the best way to print a wall mount guitar holder. This design is very simple and distributes the load of the guitar along the layers well. The 45mm file will fit most standard 6 string guitars, the neck should be slightly thinner...
thingiverse
Mounting solution (holder) for Mini PC like "HP 260 G2", "HP 260 G3" and all other VESA-compatible devices I needed a simple and inexpensive solution for attaching a mini PC to a display. But branded mounts from HP are expensive, so this solution was...
myminifactory
Mounting solution (holder) for Mini PC like "HP 260 G2", "HP 260 G3" and all other VESA-compatible devices I needed a simple and inexpensive solution for attaching a mini PC to a display. But branded mounts from HP are expensive, so this solution was...
thingiverse
Wall Mount Holder for Xiaomi thermometer(LYWSD03MMC) using stapler.
thingiverse
Cabinet mount/holder for KitchenAid Blender KHBV53AQ. Might hold others. ... Print in uploaded orientation without supports.
prusaprinters
This is wall mount/holder for Lego BrickHeadz, printed from PETG, 0,15mm. ...Diameter screw - 4mm. Print instructionsThis is wall mount/holder for Lego BrickHeadz, printed from PETG, 0,15mm.
cults3d
... other printer with rails... ... Is mounted into the rail. There is a baseplate (connection plate....) for left or rightsite rail. You can print as many arms (Arm_60_leicht.stl) as you need. You need M6x35mm screws plus M6 nuts to mount the holder.
pinshape
SummaryFlat Panel TV mount / holder. ...http://goo.gl/WyievDPrint SettingsPrinter Brand: MakerBotPrinter: MakerBot ReplicatorRafts: NoSupports: YesResolution: 0.2Infill: 30Notes: number of shell = 3