mount kinect 3d models
342424 3d models found related to mount kinect.thingiverse
This camera mount is designed for the UR robot series in combination with the Xbox 360 Kinect. ... Tools required: Number 7 spanner 4x M4 hex head 25 mm bolts 4x washers 4x M4 nuts
thingiverse
Desktop Mount/Stand for Kinect Raspberry Pi Scanner By https://www.thingiverse.com/l_k3/ https://www.thingiverse.com/thing:698577 Fits bottom slot of handle easily and is best printed vertically to save time/material
thingiverse
My very cheap targus tripod appeared to have a smaller quick release bracket than the more expensive ones. Also I couldn't print the original thing that I remixed here without support because there was a small rise in two sections of the bottom. So...
thingiverse
*I originally remixed it from a mount design here on Thingiverse but I cant find the original anymore.If you found it, please message me* Mount designed to fix a 360 Kinect to a celling. Thinking about adding more parts so you could also mount is in...
cults3d
There are probably better ways to make this but I wanted one print that would work for a tripod and two Xbox Kinects. ... You can stick a 3/4' dual rod
thingiverse
There are probably better ways to make this but I wanted one print that would work for a tripod and two Xbox Kinects. ... You can stick a 3/4' dual rod
thingiverse
This is a small project to mount a Kinect on a standard Camera tripod. Instructions This is the first version and it needs a little work but the basics are there. The files provided allow you to cut...
thingiverse
to mount the Kinect. ...Print Settings Printer: Flashforge Dreamer Rafts: Yes ...
thingiverse
I needed a base to mount the Kinect so I designed this in OnShape and printed it out. It uses one 1/4-20 threaded insert from McMaster-Carr; part number [90975A025](https://www.mcmaster.com/90975a025). Spring clips are printed separately so that...
prusaprinters
I needed a base to mount the Kinect so I designed this in OnShape and printed it out. ...It uses one 1/4-20 threaded insert from McMaster-Carr; part number <a href="https://www.mcmaster.com/90975a025">90975A025</a>.<br/> Spring clips are printed...
thingiverse
This mount is for a LG 55lw5600 LED TV. ...Use a 1/4-20 bolt of your choice to secure the Kinect sensor to the mount.
thingiverse
But his mount is good when printed in ABS, else the locking tabs that goes in to kinect base can break when printed in PLA. I very much liked his design, but then decided to redesign the whole mount to be able to print it in PLA. This mount can be...
thingiverse
This is for mounting a DSLR Camera over a Kinect to use with the RGBDToolkit www.rgbdtoolkit.com Took some parts from this thing:http://www.thingiverse.com/thing:13184 Instructions You'll need: Qty - Item/Piece 6 - 1/4"-20 hex nut 4 - 1/4"-20 x 1"...
thingiverse
I needed to permanently mount the Kinect inside the backbox of my virtual pinball machine, but none of the mounts seemed to have screw down mounting ears. I added two mounting ears/bosses that you can use to permanently mount the Kinect using...
thingiverse
Works well for TVs that are wall mounted so you can mount the Kinect close to the TV (above or below it). Instructions Print using ABS or Nylon (PLA may work, but I haven't tried it) using 25%...
thingiverse
This is a simple mount for the Microsoft Azure Kinect to a Manfrotto 785B Tripod using a 1/4" 20 screw 3/4" long.
thingiverse
Camera screw mount for the Kinect with quick release buttons. ...Print 3 parts, assemble as shown with a ballpoint pen spring.
thingiverse
Kinect Mount for 27" Sceptre TV Instructions Can be made with or without supports. ... If made without supports some smoothing may need to be done on upper lip if built on side.
prusaprinters
... mount for the Kinect with quick release buttons. ...Print 3 parts, assemble as shown with a ballpoint pen spring. Post-Printing Assembly Insert the two locking arms and add a ballpoint pen spring as shown in the picture. Category: Tool Holders & Boxes
thingiverse
Needed a mount for an installation, took a quick look and found some other nice ones on here. Decided to make mine from scratch cuz I like to have parametric models. ...This is one more option you can try, I went for an aesthetic match of the base of...
thingiverse
I wanted a stable undershelf mount for the Xbox 360 Kinect. its being used for full body tracking and it needs to remain in the same exact spot for accurate calibration. T his mount is two parts the mount and a top plate that is optional use can use...