mounting boss 3d models
353670 3d models found related to mounting boss.thingiverse
This plant pot model features both an integral saucer with six drain holes to the saucer and a side boss with blind hole to receive a 9mm OD telescoping pole mount for a halo type LED grow light. ...The pot's dimensions are 100mm ID x 113mm deep.
thingiverse
... where tolerances might want to be tweaked to get a good fit, eg when including screw holes as part of 3d printed parts. These models are ideal for adding/subtracting to/from your existing models to make clearances or mountings for common fittings.
thingiverse
Mount the part in a dropout with a 12mm thru axle like it is a wheel, press it flat against the dropout, and rotate it so the little nubs fit in the brake mount holes (yes, you need to remove your brake calipers first). The nubs should fit in the...
thingiverse
This is a remix of the ELP 8MP holder which was designed for 1/4 20 mount by peteroakes modified to fit onto the ELP Camera Mount for Boss LS-1420 by micvee. ... This will mount the ELP 3.8mm 8MP camera found here...
thingiverse
This is similar design to Rockboard QuickMount inserts for mounting guitar pedals to Rockboard pedalboards. Unfortunately Rockboard doesn't offer(yet) a solution for Boss FS-7 dual footswitch. Notes: - in order to prevent clips from braking upon...
thingiverse
This is a Realacc UXII antenna mount for the Boss XL frame. It may fit other frames too. The spacers (center-to-center) are 31mm apart. This should allow the antenna to be tucked safely away very close to the frame and out of the way of the...
thingiverse
This is similar design to Rockboard QuickMount inserts for mounting guitar pedals to Rockboard pedalboards. Unfortunately Rockboard doesn't offer(yet) a solution for Boss RC-10R rhythm looper station. Notes: - in order to prevent clips from...
thingiverse
This Camera mount is designed to mount the ELP camera model # ELP-USB500W02M-L21 to the 5th Generation Boss Laser LS-1420/1416. It may work with other models of ELP camera and it may mount to other models of Boss laser, but I have not tested any...
thingiverse
Pedal board mount for Boss effect pedals. Screw your pedals directly to your pedal board. No messing around with velcro. ... Any screws with a shaft thickness of 4mm or smaller should fit.
myminifactory
... Boss Mount (PRESUPPORTED)Please note that this miniature requires a base. ...The bottom part of the model is considered a base topper to allow better grounded/ gluing to a base :) Lizardman Clan Boss on dinosaur mount with a variety of weapon option!
thingiverse
I made some mounting brackets for the BOSS SY-1000 synth effect pedal to fixate it on my board. ... Supports may be needed for the version with screw holes.
thingiverse
This is a simple mount that i used to place my GT-1 on the side of my desk.
thingiverse
No nonsense holder/mount for a jack-plug (and/or the WL-T). ... Can be mounted on a horizontal or a vertical surface. I used double sided tape. ... Minimal design, pure functionality - let me know if you want a fancier version.
thingiverse
added tangent chamfers to the hinge pin bosses on the original model. ...I had the original fail on me due to the bosses snapping off when tightening, so I made this with the hopes of preventing that. ...will report back if this upgrade works better!
thingiverse
This is an AXII antenna mount for the Boss XL/Medium frame that fits the AXII antenna from GetFPV. If you have a Realacc AXII, this will NOT fit it. I printed this mount out of TPU and it is flexible enough that it should survive most crashes and...
thingiverse
This mount is designed for the Boss XL or Medium frame and to used with an extension. It should work with either a hex mount or one with the flange pieces coming out the sides. You shouldn't have to use the screw holes with the flange extensions, but...
thingiverse
There is a 30 degree version of this mount as well: https://www.thingiverse.com/thing:2944341 ======== Team Neugen Frames ======== Boss Medium frame: http://spyderbyte.miiduu.com/team-neugen-boss-medium Boss XL frame:...
thingiverse
My loop station kept moving away from the footswitch so I designed a mount that will keep them together on stage. The mount slides onto the t-slot designed for modular systems of pedals. ...Enjoy!
thingiverse
... is impossible to get tension into the screws when tightening onto plastic. I remixed this to allow for the mounting of some metal bosses. I used 7mm OD, 3mm ID, 5mm thick aluminium bosses and epoxied them in. ... Hopefully no issue from here on in.
thingiverse
This is a mount for the Boss XL or Medium frame that will hold the RunCam Eagle micro back a little further in the frame to help protect it in a crash. The hole for the spacers is 4.9mm, instead of 5mm. This will make the fit a little more snug and...
thingiverse
Step 4 Screw the Boss RE-20 aluminium panel with the 3D printed front panel with two of the Boss RE-20 aluminium panel screws together. Widen the holes for the screw on the top of the aluminium panels with a drilling machine (or similar) until the...
thingiverse
Used to mount the manual speed controller to Kyosho's Car Crusher series RC trucks. ...Big Brute, Hi-Rider Corvette and Big Boss.