mouse cord 3d models
28749 3d models found related to mouse cord.thingiverse
This is a low profile slim mouse cord holder for mouse cables <2.5mm in diameter.
thingiverse
You will need: Double sided tape This nifty mouse cord holder has 2 advantages to other designs! 1. You can stick it with tape wherever you like 2. The cord does not escape! Just adjust correct length and forget about it :) Enjoy! ...
thingiverse
A little twist clip for keeping mouse cords from becoming a rat's nest. It was inspired by muzz64's Tidy Tail (https://www.thingiverse.com/thing:2411911), but was created from scratch for the cable size and wall thickness I needed. (designed for a...
thingiverse
This was designed to organize the USB plug and cord for a basic Inland mouse. ... The notch for the cord may need to be adjusted if your cord is a little thicker.
thingiverse
This a mouse holder that I designed to hold the cord above the mouse pad. The hole is 3/4 of an inch, so it should be able to accommodate any usb plugs. To use, print it off, then put the legs under your mouse pad. Finely you put the cord threw the...
thingiverse
Got tired of my extra cord from my mouse in the way so I made this! ... USE: Set desired amount of length for your use case and simply pull that section through the hole.
thingiverse
Just a 15 minute make I sketched up to hold the cord on my mouse so it doesn't fall off my desk. I didn't like the ones that were currently on thingiverse, as I wanted one that held the cord tightly, not just the end. I have a logitech G403 gaming...
thingiverse
... and a half and shows no signs of damage or even wear. The bungee holds the cord in place, but can be very easily adjusted around, because the design allows it to be pulled through easily when pulled in a direction that is parallel with the cable.
thingiverse
The cable on my mouse (Logitech G302) was also a little too large to fit into the groove comfortably, so, added a bit of a bigger inner channel for that to lay in. I found that the base also is really light, but, a bit of double sided adhesive made...
prusaprinters
The cable on my mouse (Logitech G302) was also a little too large to fit into the groove comfortably, so, added a bit of a bigger inner channel for that to lay in. I found that the base also is really light, but, a bit of double sided adhesive made...
cults3d
Flexible mouse bungee for attaching to the back of your table. Use TPU or similar for the rods, and PLA or whatever for the rest. ...I recommend 95A TPU.
thingiverse
Flexible mouse bungee for attaching to the back of your table. Use TPU or similar for the rods, and PLA or whatever for the rest. ...I recommend 95A TPU.
thingiverse
This is a very simple clip on mouse cord bungee/clip designed for the Benq XL2420Z 144hz gaming monitor and perhaps others featuring the same plastic bezel and rear casing size. The cable route fits a ~3mm braided mouse cord secured by "stealthed"...
thingiverse
Made this for my Logitech G502 mouse, pretty sure it works for others as well! ... Cord Length of G502: 6ft.
thingiverse
I've always wanted to own a computer mouse bungee cord holder, but i didn't want to spent money on it, so i printed mine.
thingiverse
A small, minimalist, wire holder, i have glued it place on my desk with double sided tape.
thingiverse
Customized version of https://www.thingiverse.com/thing:571542 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=571542
thingiverse
End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515
prusaprinters
<p>A small, minimalist, wire holder, i have glued it place on my desk with double sided tape.</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>Geeetech i3 Pro B</p> <p class="detail-setting rafts"><strong>Rafts: </strong>...
thingiverse
Mouse Bungee F2 sostiene el cable del mouse para que se mueva libremente. El trabajo esta en progreso. debo hacer que sea mas pesado y mas adherente a la superficie del escritorio. Se puede probar usando una cinta adhesiva doble. Son 2 piezas...
thingiverse
Customized version of http://www.thingiverse.com/thing:1241976 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1241976
thingiverse
Love my Corsair MM800 mousepad, however occasionally my mouse cable would get hung up just enough to throw me off on the bump on the back. I designed this thing so the sides of the bump are more gradually sloped, preventing hangups from your mouse...
thingiverse
Este clip sirve para sujetarlo a la goma de la mascarilla y que pasando una goma por tu cabeza sirva para que no te moleste la goma en las orejas. ... CLIP SALVA OREJAS EARS SAVERS CLIP FACE MASK MOUSE TAIL CORD https://youtu.be/vJJyYf-mITY
thingiverse
Reproduction of this cable claw with screw holes (M3) https://www.amazon.fr/Akwox-Organisateur-Management-Chargeurs-Téléphones/dp/B01KFQB5WA Five slots with flexible size: Design with 3pcs 5.0mm slots and 2pcs 7.5mm slots, flexibly fit large...
cults3d
This holder will keep your mouse cord from bothering you during your work, gaming, recreation, or whatever you may do! I spent many hours designing this so that it would print nicely and serve its function. ... Mouse bungees are outrageously expensive...
thingiverse
... Notes: Print how they are oriented, use supports everywhere (off bed and off print) and 30% infill or more. Post-Printing After Printing You may need to sand mouse cord slot depending on size of your cord.
thingiverse
Cable bungee to organize your mouse cord. ...The spin is designed to be thin enough to bend but not thin enough to break can use double sided tape or velco to stick it to the desk