moza mods 3d models
33134 3d models found related to moza mods.thingiverse
Bush to go inside the spring on SRP brake pedal. Print from TPU Around 65% gyroid infill. Works well with the standard spring and bush. Use either one 20mm or two 13mm depending on how much initial brake travel yo want. ... Height can also be easily...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=677959 Instructions Using the following options: neodym_1_height = 3.5 big_heart_outline_level = 8.0 neodym_2_height = 2.5 outline_width = 2 text = Moza text_level = 8.5 text_height = 16...
thingiverse
As the table clamp is hard to get a hold of I designed this simple jig to fix the Moza R9 base to my desk using glue clamps. Will get some C-clamps in the future if I don't switch to a more permanent wheel base. Should work just fine even though...
thingiverse
Here are the parts I made to mount my moza r9 to my desk. You may have to slightly redesign the bottom clamp to better fit your desk since mine had a ridge that fit in the groove I made. You will also need some screws, nuts and washers for the...
cults3d
This is to keep your Moza Air 2 from spinning freely. ... It requires the SmallRig mounting clamp.
thingiverse
... and dirty mount of bwoo's excellent VoCore 4" Dashboard. ...I'm basically adding a mount for the Moza R5/R9. Please print out the enclosure from bwoo's models, and then the bracket I add here to mount to your Moza R5/R9 wheel base using m3 screws.
thingiverse
I've remixed Fanatec DD1 PSU 80x40 aluminum profile mount. ...This one is for Moza R9 wheel base power supply. Made walls a bit thicker to be printed more easy and better quality. ...
thingiverse
Wanted a way to keep the passively cooled Moza R9 cooler during long sessions. This simply slips over the backside and stays in place on its own (if the base is bottom mounted). Clearance has been kept for cables and power button. I printed in...
thingiverse
Gimbal stand for the Gudson Moza Air Gimbal. Maybe it fits for your gimbal too, the tube have a diameter of 29mm. The Surface of the printed ABS-parts are refined with acetone. Optional: You can print the "parking" part (Parkp-Oben) two...
cults3d
Gimbal stand for the Gudson Moza Air Gimbal. Maybe it fits for your gimbal too, the tube have a diameter of 29mm. The Surface of the printed ABS-parts are refined with acetone. Optional: You can print the "parking" part (Parkp-Oben) two times and...
thingiverse
Mount for 3.5"dashboard for moza R9 Needed material: 6 to 12 M2 8mm screws and nuts (you can either use 2 diagonal or 4 screws for each thing) 8 to 24 12mm diameter magnet (depends on their strenght and thickness, can accomodate up to 4mm thickness)...
prusaprinters
EDIT added V2 components, now the magnets are force mounted but can get away easily thanks to a cut on both sides, does not need magnet cover anymore, and only one magnet per hole is enough. Mount for 3.5"dashboard for moza R9Needed material:6...
thingiverse
Just a Spacer for the Springs of the Break Paddle of the Moza
thingiverse
This is a mount for svideo's 140mm max airflow fan housing for sim racing (https://www.thingiverse.com/thing:3843782). ... I needed a bracket to mount the fans to MOZA R5 wheelbase. ...
thingiverse
... would not mount despite its bag of sundry holders. ... The first version in the photo showing the mount w/camera on the MOZA has some extra mass that does not contribute to strength so the second version (FreeCad generated screen shots) is posted.
thingiverse
... a bit looser fit. Adapter to fix the MOZA SRP pedals to the playseat challenge frame (which doesn't have any screwholes or other). Intended to be used with the included bolts. ... Make sure to duplicate and mirror the model before printing.
prusaprinters
Used to get power from the 12v pads on the Moza wheelbases, I used the screws, springs and nut from the horn connector on the Kyostar through the holes to face the pads. I then cut an old pen spring in half, soldered that to a red and black wire...
thingiverse
This is adapter plate to replace Moza R9 wheelbase knob and to allow use of common aftermarket steering wheels with 70mm PCD. Unscrew knob (6 hex screws) from base and carefully remove the connector inside. Print this adapter plate and use...
thingiverse
Modified the fanatec pedal adapter and used it completely differently and modified for the MOZA SR-P pedals A lot of holes because my legs are short and even on the closest setting the pedals were not at a comfortable place The pebbles are here to...
thingiverse
As it's taking forever for my Moza GS wheel to arrive and I already have the R9 wheel base and pedals I decided to print quick release and a simple wheel for use in the meantime. The quick release connects to the shaft with little "nubs" that get...
prusaprinters
Modified the fanatec pedal adapter and used it completely differently and modified for the MOZA SR-P pedalsA lot of holes because my legs are short and even on the closest setting the pedals were not at a comfortable placeThe pebbles are here to...
thingiverse
Thanks to 9klifestyle, I mod his adapter for make a wall mount. ... Printed with cura standard setting on ender 3 v2
thingiverse
Moza R9 Iphone 11 Mount. ...Needs 4 30mm M3 nuts and bolts
thingiverse
Customized version of http://www.thingiverse.com/thing:2016538 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2016538 Instructions Using the following options:...
thingiverse
QR Wheel holder with screw holes This product is an improvement from another mount. ...I have made the base length longer to ensure the QR does not hit the mounting plate, which happened in the old model.
thingiverse
I liked this mounting option, but the stem height is too big, it rests on the steering wheel contacts. Therefore, I made a recess. ... I also made conical recesses for countersunk screws.