mqc fusion 3d models

MQC Fusion TX, RX mount

This is a hard (PLA) mount for the MQC Fusion.

immortal T mount for MQC Fusion Quadcopter frame with unify style vtx antenna mount

MQC Fusion Go Pro mount for a session, 4 and 5. ...For assurance that it wont dislodge use washers between screw head and mounting feet.

MQC Fusion split V2 parts -adjustable go pro mount -receiver mount for crossfire micro or others so that you don't have to attach anything to top plate -Battery Lead cable management loop goes on standoffs -Gps Sleeve For BrainFPV GPS

This is my attempt to create an electronics mounting system for the MQC Fusion. With this mount you can side mount a VTX and FrSky X4R. There are notches for zip ties, holes on the back for antennas to go through, and mounting tabs for zip ties...

35 Degree Gopro mount for the Mini Quad Club Fusion. Designed to print without supports. ...My photo was printed with the FT-5, no supports at .24mm resolution at 32mm/s

35 Degree Gopro mount for the Mini Quad Club Fusion. Designed to print without supports. ...My photo was printed with the FT-5, no supports at .24mm resolution at 32mm/s

A ComDock for the Mini Quad Club Fusion frame, intended to be used as a mount for the VTX, RX and antennas. ... **Note:** The support under the RX lower antenna tube mount is intended to be cut off after printing.

GoPro Hero 5 Session mounts for the MQC Fusion. Ranging from 10 to 25 degrees pitch. Tell me if you want me to change or add something and I'll get right on it. ...=) Safe flying!

This is a mount for both the Lumenier Axii stubby antenna and the TBS imortal-T antenna mount to the rear of the MQC Fusion frame. Should be pretty self-understanding how everything fits but comment if you have any questions. ...The footprint for the...

MQC Fusion 30 Degree HD cam Mount. This mount will work for Yi, Session and Hero. It was designed for the Gopro Session. I designed this because I got tired of my Session Ejecting in a crash. ...This will hold the Session in place and double as a lens...

This will replace your current side plates on the MQC Fusion. It will give your camera several locking positions 0,15,30,45 degrees. You might need longer screws for the bracket of the Hs117. You also need some M2.5 screws to secure the degree...

... 6/12/2019: I have filleted all edges so that there is no possibility of layer separation. ...This was suggested to me by Brent Collier. This is a GoPro couch for the Mini Quad Club Fusion V2/Fusion Split V2 frame. ...This mount is set at 30 degrees.

THIS MOUNT WILL FIT OVER THE REAR STANDOFFS OF THE MQC FUSION V1 PERFECTLY AND ALLOW YOU TO MOUNT A RUSH TANK VTX TO IT. I WAS ABLE TO STUFF A BIG CAP AND MY TBS NANO RX NO PROBLEM UNDERNEATH THE MOUNT. I HAVE A FEW OTHER VERSIONS I MAY UPLOAD FOR...

V1 - This is a mount for the gopro hero 5 session to fit, and protect it while mounted on the MQC Fusion frame. fixed at 30* V2 - widened the frame to offer more side protection to the GP, thickened the base to 4mm to prevent tear-out at the screw...

Needed a GoPro Hero Session 5 Mount for my MiniQuadClub (MQC) Fusion quad frame that works with Reelsteady software. If you use a Hero Session 5 with Reelsteady, you need certain GoPro mounts that filter out certain frequencies in the raw footage...

Designed this antenna holder to allow for play when you crash. since its use i've notice a reduction in both antenna breaks and sma connector breaks. designed for use on 20mm standoffs (like the split or the no longer available slammed versions) but...

Print in TPU on its right side (as facing out - opposite of lens side) with supports to minimize the filament used. ... This is V5 of my hero 8 mount and so far the only one out there like it.

for best durability print in TPU for best skidding abilities print in PLA or ABS, but it will be brittle and break easier - try 100% infill to combat that here

Hop on the Hype Train!! Soft mount your motors to reduce vibrations to the FC. These will also protect the edges of your carbon Fiber. The spacer is 2mm thick under the motor and around the arms. ...Print out of TPU with desired infill, Preferably 100%.

Since the session 5 is no longer, i created the GoPro Hero 5/6 mount for the MQC Fusion frame. I also integrated a spot to mount the TBS Immortal T for crossfire users. The tube that holds the antenna wire was designed to exit through the biohazard...

Customized version of https://www.thingiverse.com/thing:1148986 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1148986

Customized version of https://www.thingiverse.com/thing:4681765 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4681765

Customized version of https://www.thingiverse.com/thing:1148986 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1148986

Simple GoPro mount for the MQC One. ...Print Settings Rafts: Doesn't Matter Supports: No ...

the canopee for m3 frame by mqc ,, 40mm tall, with mounting holes in top for camera bracket ,, has been working solid for me for a month now.... ... awesome warranted 3 inch frame

This is similar to other micro mounts but sized perfectly for the MQC SXR. Print in TPU of your choice. ...TPU Such as SainSmart seemed to work best.

got bored and created my own gopro cage for the MQC XHD. i love the ones that the mini quad club offers. it has gone thru hell and back. but i wanted to create something with my own idea. granted its not weight conscious at all. ...but its my kinda fun...

Got a 7mm and a 10mm Lower plate spacer or skirt for the MQC One here. Both are designed for the Hovership Thruster Bar Tail LED Strip. ...Always remember to use a 9-12v regulator on the Thruster Bar or it will melt the spacer!