mr steele frame 3d models
148905 3d models found related to mr steele frame.thingiverse
Quadcopter frame, designed to be 3d printed and inspired by the Apex frame from ImpulseRC. Print queue: 4x arm.STL 2x armbrace.STL 1x bottomplate.STL 2x camholder.STL (one needs to be mirrored) 1x midplate.STL 4x standoff.STL 1x...
thingiverse
adapter plate to fit the runcamNanoHD sensor in a swift v2 mr_steele cam. ...(gopro lens) https://youtu.be/qJ5gG9Mzdz4
thingiverse
Check out my GIVEAWAY of signed mustaches by Mr Steele: https://www.youtube.com/watch?v=EjGfJOEImEw&t Now you have the chance to print your own one! I printed mine in TPU so it just bends on crash impacts. ... My YouTube Channel:...
thingiverse
just a little fun part to store the mr.steele earbud right on the goggles. mount the part to the headstrap plug your earbud to the goggles and the earbud buddy takes care of your speaker. ... - v1 is to clip to the headstrap - v2 is to pull...
thingiverse
Steele Apex, so designed a special air unit/Antenna mount. You must remove 2 standoffs to install this kit and use 20x20 stack. Print the air unit mount and antenna mounts of TPU 98A, so they are rigid enough. This way the air unit and mount are...
thingiverse
Ant Nano Camera Adapter for Steele Frame. Attached mechanically by fitting the frame holes. ... TILT_ANGLE is 30 degrees by default.
thingiverse
Hey there! ...Are you looking for a SMA antenna mount for the Steele 5 FPV Frame? Well you found it! ...It also has 2 holes for the reciever.
grabcad
Here you can find a 3d printable upgrade for your STEELE 5 frame. ...This protector will help you to avoid expensive damages to your motors and frame.Material needed:-M3x8 screw (x4)-M3x10 screw (x1)-M3 nut (x1)-Washer for M3 screw (x1)I suggest to use...
thingiverse
Compatible moteurs TBS Mr.Steele 2306 2345Kv. Diam. bobines : 22.85 mm Diam. bas moteurs : 27.60 mm Haut. bobines : 8.30 mm Plus il y aura de remplissage plus le support sera costaud, pour ma part entre 30 et 40% cela suffit. ...
thingiverse
0,5 mm full infill use double sided tape or grab a needle and stitch it up
grabcad
Here you are!!! ...A detailed 3D model of the famouos STEELE 5 frame!
thingiverse
- Added moustache Original : https://www.thingiverse.com/thing:1141381 For heat shrink : https://www.thingiverse.com/thing:2729553 Mini Wrench : https://www.thingiverse.com/thing:2729506
thingiverse
Stop wind noise with the Mic Shield! ... Sandwich the shield between the bottom plate and the center plate to hold in place.
thingiverse
Here are several parts that I have drawn and that I use on my drones. I hope they can be useful to someone. ...Printed in filaflex.
cgtrader
It is a motor frame for MR elevator systems designed as parametric by sheet metal for manufacturing with real dimensions.
thingiverse
You'll find here some extensions designed and tailored especially for Flywoo Mr Croc 7 inches quad rotor frame. Thing #1: Support_Backside.stl This is a multi-purpose rear support which can carry GPS, VTX and RX antennas. The outside part of...
thingiverse
Customized version of https://www.thingiverse.com/thing:2222566 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2222566
thingiverse
Customized version of https://www.thingiverse.com/thing:5343126 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5343126
thingiverse
Customized version of https://www.thingiverse.com/thing:1148986 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1148986
thingiverse
... version of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: pen_length = 130 font_scale = 2.2 word = Steele font_spacing = 0.85
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1074909 Instructions Using the following options: fontSize_3 = 5 fontSize_2 = 4 fontSize_1 = 5 line_3 = line_2 = Steele line_1 = R.I.P
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1039106 Instructions Using the following options: labelWidth = 60 labelRadius = 3 labelHeight = 20 textFont = Oxygen textDepth = 0.7 clipDepth = 1 clipRadius = 3 charSpacing = 1.1 text = STEELE...